Ariens 926078 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 34

background image

EN - 19

ADJUST SPEED SELECTOR

LEVER

1. Place unit on blocks with wheels / tracks

off the ground.

2. Remove hairpin from trunnion and

remove trunnion from bell crank.

3. Loosen jam nut on shift rod.
4. Start the engine and engage the traction

drive clutch.

5. Move the bell crank to the position at

which the wheels / tracks stop moving
and then stop the engine.

6. Move the speed selector lever to neutral

position and hold lever in place.

7. Without moving the bell crank, thread

trunnion up or down the shift rod to align
with bell crank hole.

8. Insert trunnion in bell crank.
9. Reinstall hairpin in trunnion.
10. Tighten jam nut against trunnion.
11. Lower unit to ground.

ADJUST ATTACHMENT CLUTCH

& BRAKE

Remove Slack from Attachment

Cable

1. Stop engine, remove key and wait for all

moving parts to stop and for hot parts to
cool.

2. Disconnect spark plug wire.
3. Loosen hardware securing belt cover to

unit and remove belt cover.

IMPORTANT:

DO NOT completely remove

hardware from unit.
4. Loosen jam nut on cable adjustment

barrel, and then turn the adjustment
barrel down to shorten cable and remove
cable slack. See Figure

Figure

29

1. Discharge Chute Gear Cover
2. Rear Adjustment Nut
3. Forward Adjustment Nut
4. Lock Arm

WARNING:

AVOID INJURY.

Improper adjustment could
result in unexpected movement
of auger and impeller causing
death or serious injury. AUGER /
IMPELLER MUST STOP within
5 seconds when attachment
clutch lever is released.

Figure

30

1. Hairpin
2. Trunnion
3. Bell Crank
4. Jam Nut
5. Shift Rod

«
...
19
20
21
22
23
...
»

Содержание 926078



































Отзывы:

Нет отзывов

Похожие инструкции для 926078

Бренд: XPower Страницы: 18

Бренд: Murray Страницы: 159

Бренд: Echo Страницы: 6

Бренд: Weed Eater Страницы: 24

Бренд: Feider Machines Страницы: 27

Бренд: HIKOKI Страницы: 48

Бренд: Honda Страницы: 36

Бренд: ebm-papst Страницы: 10

Бренд: Cub Cadet Страницы: 52

Бренд: White Outdoor Страницы: 22

Бренд: Cramer Страницы: 346

Бренд: Cub Cadet Страницы: 28

Бренд: Troy-Bilt Страницы: 36

Бренд: Weed Eater Страницы: 10

Бренд: Worx Страницы: 12

Бренд: Milwaukee Страницы: 28

Бренд: Homelite Страницы: 220

Бренд: RedMax Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды