manualshive.com logo in svg

Ariens 915035, Руководство по обслуживанию

Поделиться
Скачать
Ariens 915035 Скачать руководство пользователя страница 36

10 - 35

terminal (B) to terminal (A). Terminal (A) on the ignition 
switch supplies battery voltage to the back of the PTO 
switch on the purple lead and on to the neutral 
switches on the red/violet lead to terminal S2 on the 
ignition switch and to terminal 85 on solenoid #2. 
Terminal (A) also supplies battery voltage to terminal 
30 and 85 on solenoid #1 and on to the hour meter. 
When the operator is in the seat, battery voltage will 
transfer from terminal 30 to terminal 87 and on to the 
front terminal of the PTO switch and on to terminal 85 
on solenoid #2 in the yellow/red lead. Battery voltage is 
supplied to the fuel shut off solenoid from terminal 85 
on solenoid #2.

STEP 4

With ignition switch in the start position, battery voltage 
is transferred from terminal S2 to S1. Terminal S1 
Transfers battery voltage to the one small terminal on 
the starter solenoid and goes to ground through the 
base of the starter solenoid.
PTO clutch check out: Remove the wiring harness PTO 
clutch leads from the clutch. With a multimeter check 
the clutch coil for resistance to see if the coil is good.
The clutch used on models 915013, 015, 307 should 
have a coil resistance of (5.87-7.87) ohms. If the coil is 
bad the resistance will be higher or not at all.

The clutch used on models 915014, 016, 306 should 
have a coil resistance of (1.98-3.98) ohms. If the coil is 
bad the resistance will be higher or not at all.
Ignition switch check out: Battery voltage check in the 
"off" position, check for voltage at terminal "B". It 
should not be present on terminals A, S1, S2.
With the ignition switch in the "run" position, check for 
battery voltage at terminal B, A, S2. It should not be 
present at terminal S1.
With the ignition switch in the "start" position, check for 
battery voltage at terminals B, A, S2, S1.
PTO switch check out: The PTO switch is a push/pull 
switch with normal open and closed contacts. Power 
transfer should be checked with a voltmeter. The 
switch contacts should be checked with an ohm meter 
with the wire harness plug removed. The light switch is 
similar to the PTO switch with only one set of contacts.
Diode check out: Diodes are checked with an ohm 
meter set on the diode check, and should only pass 
voltage in one direction. If it passes voltage in both 
directions or not at all the diode is bad and needs to be 
replaced.

.
Normally open contacts manually activated. contact 
resistance is 0.1-0.3 ohms when correct.

 

Содержание 915035













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды