manualshive.com logo in svg

Ariens 915035, Руководство по обслуживанию

Поделиться
Скачать
Ariens 915035 Скачать руководство пользователя страница 10

4 - 9

Safety Interlock System

4.2  FUEL LEVEL

Fuel Shut-Off Valve

Use this valve to control fuel flow from left (1) or right 
(2) fuel tank (Figure 3).
Open the valve to operate the engine. Turn the valve to 
"Off" (3) when storing or transporting the unit.

To add fuel to the fuel tank:

1. ALWAYS place unit in open or well ventilated area.
2. Stop engine and allow to cool for two minutes.
3. Clean fuel caps and surrounding area to prevent 

dust, dirt, and debris from entering fuel tanks.

4. Remove fuel caps.

IMPORTANT: 

See Engine Manual for correct type and 

grade of fuel.

5. Fill fuel tanks to 1/2 in. (1.3 cm) below bottom of 

filter neck. See 

Specifications

 for capacity of fuel 

tanks.

6. Replace fuel caps.
7. ALWAYS clean up any spilled fuel before starting 

the engine.

4.3  MAINTENANCE SCHEDULE

WARNING: 

Safety interlock failure and 

improper operation of unit can result in death 
or serious injury. Check system before each 
use to make sure it is functioning properly.
Perform the following tests to ensure the 
safety interlock system is working properly. If 
the unit does not perform as stated contact 
your Ariens/Gravely dealer for repairs.

Test

Steering 

Lever

PTO

Parking

Brake

Engine

1

Neutral
Lockout
Position

Off

Engaged

Starts

2

Forward

Off

Engaged

Doesn’t 
Start

3

Neutral
Lockout
Position

On

Engaged

Doesn’t 
Start

4

Out of
Neutral 
Lockout 
Position

Off

Disengaged

Doesn’t 
Start

5*+

Reverse

Off

Disengaged

Shuts Off

6*+

Neutral 
Lockout 
Position

On

Engaged

Shuts Off

7*+

Out of 
Neutral 
Lockout 
Position

Off

Disengaged Shuts 

Off

* Test with engine running.
+ Operator lifts off seat.

WARNING: 

Fuel is highly flammable and its 

vapors are explosive. Handle with care. NO 
smoking, NO sparks, NO flames.

CAUTION: 

Before performing any service or 

adjustments:

• Turn PTO switch "OFF".
• Park mower on a hard, flat, level surface.
• Place steering control levers in neutral 

lock (fully outward) position.

• Set parking brake.
• Turn ignition switch "OFF" and remove 

key.

• Wait for blades and all moving parts to 

stop.

WARNING: 

AVOID INJURY. Read and 

understand the entire 

Safety

 section before 

proceeding.

RIGHT

TANK

LEFT

TANK

OFF

OF1881

1

2

3

Figure 3

Содержание 915035













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды