Ariens 911413 - WAW 34 Скачать руководство пользователя

Страница: 21 / 30

GB - 21

BELT REPLACEMENT

Wheel Drive Belts

1. Stop engine, remove key, wait for all

moving parts to stop and hot parts to

cool.

2. Raise and support the rear of the unit.
3. Remove the rear cover and disconnect

the neutral return springs from the spring

anchors.

4. Remove the idler arm from the

transmission plate. See Figure 15.

5. Remove the forward drive belt from the

engine pulley and remove it from the

unit.

6. Remove the reverse drive belt from the

engine pulley and remove it from the

unit.

7. Route the new reverse belt through the

transmission idler arm and then install

belt on the engine pulley. See Figure 15.

8. Route the new forward belt through the

transmission idler arm and then install

belt on the engine pulley. See Figure 15.

9. Install the idler arms on the transmission

plate and install the belts on the

transmission pulleys. See Figure 15.

10. Replace the rear cover.

11. Start the unit and test operation of the

drive system. Adjust the wheel drive

controls, if needed.

NOTE:

Check the wheel drive control

adjustment after the first 25 hours of use to

compensate for belt wear.

WARNING:

AVOID INJURY.

ALWAYS block wheels, engage

parking brake and know all jack

stands are strong, secure and will

hold weight of unit during

maintenance.

Figure 14

Disconnect neutral return
springs from the spring anchors.

Figure 15

1. Engine

Pulley

2. Idler Arm

3. Reverse

Drive Belt

4. Forward

Drive Belt

Rear of Unit – Forward Drive Belt Routing

Rear of Unit – Reverse Drive Belt Routing

Содержание 911413 - WAW 34































Результаты поиска

Содержание 911413 - WAW 34

Отзывы:

Похожие инструкции для 911413 - WAW 34

Бренды по названию

Популярные бренды

Ariens 911413 - WAW 34, Руководство владельца/оператора

Результаты поиска

Содержание 911413 - WAW 34

Отзывы:

Похожие инструкции для 911413 - WAW 34

Бренды по названию

Популярные бренды