Ariens 624E Скачать руководство пользователя | Manualshive

Страница: 21 / 30

background image

GB - 21

TRACTION DRIVE BELT REPLACEMENT

NOTE: Housing and frame must be tipped apart and
attachment drive belt removed from engine sheave in
order to change traction drive belt (Figures 19 and 20).

1. Remove attachment drive belt (See Remove

Attachment Drive Belt on page 19).

2. Pull idler away from traction drive belt and

remove belt from idler, camshaft pulley and
driven pulley (it may be necessary to turn
camshaft pulley using recoil starter handle).

NOTE: To gain clearance, engage traction clutch and if
necessary pull back attachment idler arm.

3. Replace traction drive belt.

4. Replace attachment drive belt (See Replace

Attachment Drive Belt on page 20).

ATTACHMENT CLUTCH/BRAKE
ADJUSTMENT

1. Remove belt cover.

IMPORTANT: The clutch cable must be slack when
clutch lever is disengaged.

2. Adjust cable slack.

a. Position the upper cable adjuster on the

mounting bracket, if necessary, so the cable
adjuster and seal do not contact the pulley
(Figure 22).

b. With the clutch lever disengaged, loosen the

control cable mounting nuts on the
attachment clutch arm (Figure 22).

c. Pull up on the cable body to remove cable

slack.

d. Finger tighten mounting nuts and then loosen

the top nut five turns.

e. Tighten the bottom nut with a wrench.

3. Check attachment clutch lever measurement.

a. Start engine and run at full throttle.

b. Slowly squeeze the attachment clutch lever

until auger shaft begins to rotate.

c. Measure the distance from the end of the

clutch lever to the handlebar as shown in
Figure 23. The distance between the clutch
lever and the handlebar should be 6 in. - 7 in.
(15,2 cm - 17,8 cm).

d. Shut off engine.

CAUTION: Always support Sno-Thro frame
and blower housing when loosening the cap
screws holding them together. Never loosen
cap screws while unit is in service position.

WARNING: IMPROPER ADJUSTMENT
could result in unexpected movement of
auger and impeller causing death or serious
injury. AUGER / IMPELLER MUST STOP
within 3 seconds when Attachment
Clutch/Impeller Brake Lever is released.

WARNING: Adjustment procedure requires
the engine to be run with the belt cover off.
AVOID INJURY. Read and understand the
entire Safety section before proceeding.

Figure 22

OS2460

1. Upper Cable Adjuster
2. Right Hand Handlebar
3. Attachment Clutch Arm
4. Attachment Clutch Cable
5. Cable Mounting Nuts

«
...
19
20
21
22
23
...
»

Содержание 624E































Отзывы:

Нет отзывов

Похожие инструкции для 624E

SNOW ELECTRIC 45

Бренд: Stiga Страницы: 81

Бренд: Poulan Pro Страницы: 32

Бренд: GreenWorks Pro Страницы: 9

Power Max 724 OE

Бренд: Toro Страницы: 28

Power Max Heavy Duty 1128 OHXE 38803

Бренд: Toro Страницы: 36

Power Clear 721 R

Бренд: Toro Страницы: 20

1500 Power Curve 38371

Бренд: Toro Страницы: 8

Бренд: Toro Страницы: 28

Бренд: Kobalt Страницы: 80

Бренд: Toro Страницы: 20

Бренд: Dolmar Страницы: 44

Бренд: Wuyi Zhouyi Страницы: 22

Бренд: Maruyama Страницы: 28

Бренд: Maruyama Страницы: 56

Бренд: AIR FOXX Страницы: 3

Бренд: New Holland Страницы: 1

Бренд: Power smart Страницы: 14

Бренд: Troy-Bilt Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды