User manual whirlpool D-series with Bluetooth
User manual whirlpool D-series with Bluetooth
Before installation:
1.
You must ensure that water inlet, electricity and drain pipe are ready and suitable for installation of the product. We refer to the
technical specifications in this manual. Use a splash proof socket to connect the product with the power supply. The drain hose has
a diameter of 40mm. The water inlet hoses have ½”-connections.
2.
The water connection hoses are resistant to high pressure. Before you connect the hoses, flush the supply pipes first so all possible
dirt particles from the pipes are flushed out.
3.
Use taps on the jack in the wall. Any repairs or maintenance on the product can be done without having to close the main valve of
the water.
4.
Ensure that there is enough space to connect the various parts.
5.
After extracting the product parts, check that all parts are complete and that there is no visible errors, missing parts, or damages.
How to operate the faucet:
Installation instructions:
1.
Be sure that the product is installed correctly. We recommend to install the product by an expert. The product must be installed
on the floor with all feet before use. Levelling the product is an important topic.
2.
Electrical installation and testing shall be performed by approved electrician.
3.
Power to the product must meet the requirements of the product described in this manual.
4.
Protective devices for leakage, overload of power or incorrect voltage must be installed and working.
5.
Do not cut or extend electrical wires / power cord during installation of the product.
6.
Do not disassemble the control panel or computer controller as this is not designed for disassembly. Defects, damages or
shock caused by such removal can’t be charged to the supplier or its distributors.
A: Change over valve:
Water jets
Hand shower
Waterfall
OFF
Air regulator:
B: Temperature adjustment:
H for hot water
L for cold water
7.
For electrical installations the local standards must be followed.
8.
The motor must be grounded with wire not less than 1mm.
9.
Earthed appliances must be permanently connected to fixed wiring.
10.
Parts incorporating electrical components, except remote control devices, must be located or fixed so that they cannot fall into
the bath;
11.
The appliance should be supplied through a residual current device (RCD) having a rated residual operating current not
exceeding 30 mA.
12.
Parts are installed in the correct zone and that equipotential bonding is carried out.
13.
Electrical installation shall be in accordance with National Regulatory requirements.
14.
Connect the supply for hot & cold water in the right way up (red=hot, blue=cold).
15.
Organic chemicals such as acetone, ammonia or gasoline can dissolve or damage the product. Do not use these chemicals for
cleaning or installation.
16.
Do not support or stack anything on the product. Take special care when moving the product so that no pressure will be
charged unnecessary.
17.
Maintain good ventilation in the room product is installed in.
18.
Be sure that the hot and cold water hoses will not touch the floor when the product is pushed in the correct place. This will
minimize the chance of getting rust on the hoses.
Maintenance:
-
When to clean the whirlpool use a soft sponge and a detergent without ammonia and acetone to prevent the surfaces in the whirlpool
gets math.
-
The drain can be caused by hair, soap scum and such clogging. Clean the drain regularly.
-
The chrome parts are carefully polished. Do not use polishes with abrasives or other chemicals that may affect the chrome parts of your
whirlpool. Try not to remove stains with hard objects, such as knives. To clean, use a damp cloth.
-
Bad maintenance / cleaning can cause damage to the faucets and jets.
-
Clean the whirlpool with a whirlpool cleaner monthly. Follow the instructions on the bottle. Lime, soap, grease, oil, hair, bacteria and dead
skin care can contaminate your whirlpool system. If not cleaned regularly, you can get black flakes in the bath. If this happens, you
should clean the whirlpool system with a whirlpool cleaner so often in succession to clean up the black flakes and have it completely
disappeared.
Warning
: the use of cleaning materials other than those recommended by the manufacturer can result in
damage to the bath and/or the whirlpool apparatus
Warning
: To be adjusted (repaired) only by installers who can demonstrate to the appropriate authorities awareness and competence in the
application of National Regulatory requirements for safety, i.e. electrical and water supply/disposal
Page 3 / 9
Page 8 / 9
Содержание Whirlpool BT series
Страница 1: ...User manual Whirlpool Serial number ...
