Argox P4 Series Скачать руководство пользователя

Страница: 61 / 75

P4 Series
User Manual

The printing position is not correct



Did you use the correct media type for printing?



The media is not loaded correctly. See Section 2.3,

“

Loading Media

”

to reload

the media.



The media sensor needs to be calibrated. See Section 3.1,

“

Media Sensor

Calibration

”

to calibrate the sensor.



The media sensor is dirty. Clean the media sensor.

Nothing is printed



The media is not loaded correctly. See Section 2.3,

“

Load Media

”

to reload the

media.



The ribbon is not loaded correctly. See Section 2.6,

“

Load Ribbon

”

to reload the

ribbon.



The print data might not be sent successfully. Make sure the interface is set

correctly in the printer driver, and send the print data again.

The print quality is poor



The printhead is dirty. Clean the printhead.



The platen roller is dirty. Clean the platen roller.



Adjust the print darkness, or lower the print speed.



The media is incompatible for the ribbon. Use the compatible media instead.

Содержание P4 Series












































































Результаты поиска

Содержание P4 Series

Отзывы:

Похожие инструкции для P4 Series

Бренды по названию

Популярные бренды

Argox P4 Series, Руководство пользователя

Результаты поиска

Содержание P4 Series

Отзывы:

Похожие инструкции для P4 Series

Бренды по названию

Популярные бренды