background image

1

Note:

 if required the next 

page can be cut out and used 
as reference throughout the 
assembly. Keep this page with 
these instructions for future 
reference.

• Assemble all parts and bolts 
loosely during assembly, only 
once the product is complete 
should you fully tighten the bolts

• Regularly check and ensure 
that all bolts and fi ttings are 
tightend properly.

Handy Hints

• Only clean using a damp cloth
and mild detergent, do no use 
bleach or abrasive cleaners. 

• From time to time check that
there are no loose screws on 
this unit. 

• This product should not be 
discarded with household waste. 
Take to your local authority 
waste disposal centre. 

Care and maintenance

Skin contact: 

Remove 

contamination by washing with 
soap and water. This procedure 
should also be followed prior to 
eating and drinking. 

Eye contact: 

Rinse immediately 

with clean water for 15 minutes 
and seek medical advice.

 

If swallowed: 

Seek medical 

advice immediately.

Glue safety 

- Take care when using glue, please follow the advice below•

Important 

– Please read these instructions fully before starting assembly

•  During assembly do not stand 
or put weight on the product, 
this could cause damage.

• Assemble the item as close 
to its final position (in the same 
room) as possible.

• Assemble on a soft level 
surface to avoid damaging the 
unit or your floor.

• Parts of the assembly will be 
easier with 2 people.

• Check you have all the 
components and tools listed 
on the following pages.

• Remove all fittings from the 
plastic bags and separate them 
into their groups.

• Keep children and animals 
away from the work area, small 
parts could choke if swallowed.

• Make sure you have enough 
space to layout the parts before 
starting.

 

• To reduce 

 

the likelihood of 

 

damaging your 

 

product please 

 

ensure that your 

power drill is set on a low torque 
setting.
• Assembly should be carried out
by a competent adult only.
• do not use this item if any 
components are missing
or damaged.
• this item is suitable for childeren
from  the age of 6.

Safety and Care Advice 

Содержание Tolga 03R 462/6071














Отзывы: