Argos Malibu 553/4038 Скачать руководство пользователя страница 11

Страница: 11 / 32

Step

Assembly Instructions

V b

1st

screw

Finished

front edge

Finished

front edge

V b

Prepare the right

divider

Fit 3 CR runners

to the right divider .

The 1st screw uses

the 1st hole in from the

front of the runner.

The 2nd and 3rd screws

. use the holes that line

up with the other panel

holes.

Fit a screw into

the hole at the top of the

runner .

Fit a rail holder to the

right divider through

the top hole with screw

and into the mark hole

drilled in the right divider.

Make sure that it is fitted

straight, in line with the

panel edges and then fit

another screw using

the lower hole.

Insert 2 large locking

cam nuts into the

right divider .

Push 2 of the quickfit

dowels as far as they

will go into the right

divider .

Tap 6 wooden dowels

into the right divider .

V b

Finished

front edge

Finished

front edge

Finished

front edge

Содержание Malibu 553/4038

































Результаты поиска

Содержание Malibu 553/4038

Отзывы:

Бренды по названию

Популярные бренды

Argos Malibu 553/4038, Руководство по сборке

Результаты поиска

Содержание Malibu 553/4038

Отзывы:

Бренды по названию

Популярные бренды