Argo 6x6 Bigfoot Скачать руководство пользователя страница 46

Страница: 46 / 60

SECTION 8

TROUBLE SHOOTING

MALFUNCTION

PROBABLE CAUSE

CORRECTIVE ACTION

(SYMPTOM)

Electric starter inoperative

1. Loose electrical connections

1. Clean and re-tighten electrical

connections

2. Battery charge low or dead

2. Recharge battery or replace as

necessary

3. Faulty starter motor

3. Return the vehicle to an Argo

dealer for servicing

Engine turns over but will not

1. Engine is cold and choke is not pulled

1. Pull out the choke and try to start

start

out

again

2. Fuel tank is empty

2. Refill tank

3. Blocked fuel or air filter

3. Remove obstruction or replace

filter as necessary

4. Carburetor adjustment too lean

4. Adjust as detailed in the engine

manufacturer’s manual

5. Spark plugs defective or fouled

5. Clean and re-gap or replace

6. Ignition system inoperative

6. Have unit serviced by a properly

trained and equipped mechanic

7. Insufficient compression

7. Take the vehicle to a factory

authorized engine repair outlet

8. Improperly operating electric fuel

8. Check that electric fuel pump is

pump or fuel shut off solenoid.

operating. Make sure fuel shut off

KAWASAKI ENGINE ONLY.

solenoid is activated to allow fuel
into carburetor.

Engine will not run

1. Refer to engine manual

Vehicle will not move or turn

1. Transmission in neutral or not

1. Place gear shift properly in gear

properly engaged in gear

2. Drive belt worn (see Section 7.2.1)

2. Replace belt if worn excessively

3. Clutch not engaging

3. Return the vehicle to an Argo

dealer for servicing

4. Transmission failure

4. Same as 3. above

5. Brakes not functioning

5. Adjust caliper or replace brake

pads

6. Idler chain broken

6. Repair or replace

7. Idler sprocket weld broken

7. Have vehicle serviced by an Argo

dealer

Vehicle pulls to right

1. Right tire pressure too low

1. Inflate all tires to the correct

pressure

2. Left tire pressure too high

2. Same as above

3. Right brake engaged

3. Make sure the steering lever is held

forward against the dash. Adjust
brake assembly if required.

4. Right side drive chain broken

4. Repair or replace

Vehicle pulls to left

1. See “Vehicle pulls to right” -

substitute right with left

Содержание 6x6 Bigfoot





























































Результаты поиска

Содержание 6x6 Bigfoot

Отзывы:

Похожие инструкции для 6x6 Bigfoot

Бренды по названию

Популярные бренды

Argo 6x6 Bigfoot, Руководство оператора

Результаты поиска

Содержание 6x6 Bigfoot

Отзывы:

Похожие инструкции для 6x6 Bigfoot

Бренды по названию

Популярные бренды