Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 256

Страница: 256 / 535

4-30

Troubleshooting Fuel

System

Fuel System (Related

Items) Table of Contents

Oil-Injection Pump................................................. 4-30
Synchronizing Oil-Injection Pump ......................... 4-31
Testing Oil-Injection Pump .................................... 4-32
Testing Oil-Injection Check Valves ........................ 4-32
Fuel Filter (1100 cc) .............................................. 4-33
Fuel Pump (CFR/Crossfire/M-Series) ................... 4-33
Fuel Pump (F-Series EFI/Z1/TZ1) ........................ 4-34
Fuel Pump (570 cc)............................................... 4-34
Gas Tank/Seat Assembly ...................................... 4-35

Oil-Injection Pump

REMOVING



NOTE: On EFI models to service the oil-injection

pump, the exhaust system and the air silencer must
be removed (see Section 3).

1. Remove the carburetors/throttle bodies and secure

them out of the way in an upright position.



NOTE: On the 570 cc, secure the carburetors in an

upright position to avoid gas from running out of the
vent tubes.

2. Disconnect the oil-supply hose from the pump and

plug to prevent oil drainage.

3. Remove the oil-delivery hoses from the adapter

plates/intake flanges.

4. Disconnect the oil-injection cable/control rod.

5. Remove the two screws securing the oil-injection

pump and retainer to the crankcase.

6. Pull the oil-injection pump away from the retainer/

crankcase and account for a gasket/O-ring.



NOTE: Remove the oil-injection pump from the

crankcase only if the O-ring or gasket need to be
replaced.

7. Turn the pump sideways; then remove the lower

union bolt. Account for two washer gaskets. Remove

the pump.

8. Remove the remaining union bolts securing the

check valves to the pump. Account for the washer

gaskets.

9. Remove the check valves. Account for two gaskets.

INSTALLING

1. In turn on each front union bolt, install a washer gas-

ket, check valve, and washer gasket; then install on

the oil-injection pump.

2. Place the gasket and oil-injection pump near the

engine; then install the lower union bolt through a

gasket, check valve, and gasket.

3. Position the oil-injection pump on the engine making

sure the oil-injection pump gear is correctly aligned

with the oil-injection pump drive gear.

4. Secure the pump with two screws (coated with blue

Loctite #243). Tighten screws to 48 in.-lb (570 cc) or

to 96 in.-lb (500/600/800/1000 cc).

5. Connect the oil-delivery hoses to the adapter plates.

Secure with clamps.

6. Connect the oil-injection cable/control rod to the

pump and secure.

7. Connect the oil-supply hose to the oil-injection pump

inlet fitting. Secure with the clamp.

8. Bleed the oil-injection system.

9. Check the oil-injection system synchronization (see

Synchronizing Oil-Injection Pump in this sub-sec-

tion). Tighten the jam nuts securely.



NOTE: On EFI models to install the exhaust system

and the air silencer, see Section 3.

Problem: Too Rich

Condition

Remedy

Diagnostic

trouble code

activated

Fuel pressure

too high

Fuel return hose

obstructed

Injectors

leaking

1. Replace problem sensor

2. Replace regulator

3. Service — replace hose — remove obstruction

4. Replace injectors

Problem: Too Lean

Condition

Remedy

Diagnostic

trouble code

activated

Fuel pressure

too low

Vent hose

obstructed

Fuel filter(s)

obstructed

1. Replace problem sensor

2. Replace regulator/fuel pump

3. Remove obstruction

4. Replace fuel filter(s)

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 256 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: