manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 259 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 259

4

4-33

3. Squeeze the vacuum pump handle and watch the

pump gauge. The check valve should release at 4.5-5

lb and again reset itself at 3.5-4 lb. If “release” and

“reset” are not within specifications, replace the

check valve.

4. Record the “release” and “reset” readings for the

valve; then perform the test on the other valve. The

“release” and “reset” readings must fall within speci-

fications and must be within 1.5 lb of each other. If

either or both are not met, replace the check valves.

5. If the check valves are within specifications but the

oil-injection usage is not, replace the oil-injection

pump.

Fuel Filter (1100 cc)

NOTE: The fuel filter should be replaced every 5000

miles.

NOTE: Before removing the fuel filter, take note of

the filter inlet and outlet for installing purposes.

REMOVING/INSPECTING

1. Open the left-side access panel; then remove the fuel

filter from the bracket.

ZJ135B

TZ118A

2. Remove the hose clamps and discard; then slowly

remove the fuel hoses from the fuel filter. Dispose of

the excess fuel from the filter properly.

3. Inspect the fuel lines thoroughly for any signs of

cracking, cuts, or wear points.

INSTALLING

1. Place the new hose clamps on the fuel hoses; then with

the fuel pump inlet and outlet noted, connect the fuel

hoses to the fuel pump. Secure with the hose clamps.

2. Secure the fuel filter to the fuel filter bracket; then

start the engine and inspect the fuel hoses and filter

for any signs of leaks.

Fuel Pump 

(CFR/Crossfire/M-Series)

0744-877

REMOVING

NOTE: Using a gasline hose equipped with a one-

way check valve, drain the gas from the gas tank. 

1. Remove the three torx-head screws securing the

access panel to the steering support.

2. Disconnect the fuel pump harness connector; then

loosen the hose clamp and remove the gasline hose

from the outlet of the fuel pump.

CAUTION

Whenever servicing the oil-injection system, use a
100:1 gas/oil mixture in the gas tank to ensure ade-
quate engine lubrication. Failure to use the 100:1 mix-
ture to the oil-injection system will result in severe
engine damage.

! WARNING

Since the fuel supply hose may be under pressure,
always wear safety glasses when removing the fuel
hoses. 

CAUTION

Since the fuel supply hose may be under pressure,
remove it slowly to release the pressure. Place an absor-
bent towel around the connection to absorb the fuel.

CAUTION

The gasline hose may be under pressure.  Place an absor-
bent towel around the connection to absorb gasoline;
then remove the hose slowly to release the pressure.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов