Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 140 / 535

2-102

Engine -

Bearcat Z1 XT/TZ1/Z1

This engine section has been organized into sub-sections

showing a progression for the complete servicing of the

Arctic Cat 1100 cc (Bearcat Z1 XT/TZ1/Z1) engine. For

consistency purposes, this section shows a complete and

thorough progression; however, for efficiency it may be

preferable to remove and disassemble only those compo-

nents needing to be addressed and to service only those

components. Also, some components may vary from

model to model. The technician should use discretion and

sound judgment. For engine-related servicing proce-

dures, see Section 3 of this manual.



NOTE: Some illustrations and photographs used in

this section are used for clarity purposes only and
are not designed to depict actual conditions.



NOTE: Critical torque specifications are located in

Section 1 of this manual.

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when servicing the engine.



NOTE: Special tools are available from the Arctic

Cat Service Parts Department.

Table of Contents

Removing Engine................................................ 2-102

Disassembling Engine ........................................ 2-108

Servicing Components.........................................2-115

Assembling Engine ............................................. 2-120

Installing Engine.................................................. 2-129

Removing Engine

1. Remove the hood and the right- and left-side access

panels.

2. Remove the two torx-head cap screws (A) securing

the console to the chassis; then lift up the rearward

end of the console and disconnect the console har-

ness plug-in. Remove the console.

743-945A

3. Remove the two screws securing the handlebar

close-off panel (B); then remove the three screws (C)

securing the left- and right-side rear spar panels to

the seat support tubes. Remove the screws (D) secur-

ing the front spar panels to the front bumper; then

remove the spar panels.



NOTE: On the turbo models, only the console and

cap screws (E) securing the left-front spar panel have
to be removed.

4. Remove the seat (see Section 8).

5. Disconnect oxygen sensor connector; then remove

the springs securing the exhaust pipe and resonator

to the engine and chassis. Remove the exhaust

assembly and account for exhaust gaskets and

springs.



NOTE: On the non-turbo models, the hairpin clip

and tab washer must be removed to remove the reso-
nator from the chassis.

TZ101A

6. Remove the negative cable from the battery; then

remove the positive cable. Remove the hardware

securing the battery to the tray; then remove the bat-

tery.

Description

p/n

Drive Clutch Puller

0744-062

Coolant Cap

0644-156

Exhaust Spring Pliers

0644-391

Exhaust Spring Pliers

0644-397

Drive Belt Deflection Tool

0644-412

Drive Clutch Spanner Wrench

0644-136

Drive Clutch Bolt Tool

0644-281

Piston Pin Puller

0644-328

Flywheel Puller

0644-480

V Blocks

0644-535

Ball Hone

0644-532

Ring Compressor

0644-378

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды