Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 153 / 535

2-115

ZJ046A

31. Remove the oil separator plates for the lower crank-

case half and account for the eight Allen-head cap

screws.

ZJ047A

32. Remove the Allen-head cap screws securing the pis-

ton cooling jets to the upper crankcase half; then

remove the jets and account for the O-rings.

ZJ054A

ZJ035



NOTE: For assembling purposes, ensure the ori-

fices in the piston cooling jets are cleared of any dirt
and/or debris.

ZJ055A

Servicing Components



NOTE: Critical engine specifications are located in

Section 1 of this manual.

Thoroughly clean all non-electrical components in parts-

cleaning solvent; then remove any carbon buildup from

the cylinder head and piston dome.

Visually inspect all engine components for wear or dam-

age.



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

PISTON ASSEMBLY



NOTE: Oversized pistons are available allowing the

cylinder to be bored oversized.



NOTE: Whenever a piston, rings, or pins are out of

tolerance, they must be replaced.

Cleaning/Inspecting Piston

1. Using a non-metallic carbon removal tool, remove

any carbon buildup from the dome of the piston.

2. Inspect the piston for cracks in the piston pin, dome,

and skirt areas.

3. Inspect the piston for seizure marks or scuffing.



NOTE: If seizure marks or scuffing is detected, the

piston must be replaced.

4. Inspect the perimeter of each piston for signs of

excessive “blowby.” Excessive “blowby” indicates

worn piston rings or an out-of-round cylinder.

Removing Piston Rings

1. Starting with the top ring, slide one end of the ring

out of the ring-groove.

2. Remove each ring by working it toward the dome of

the piston while rotating it out of the groove.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды