background image

3-33

3

3. Loosen the bevel gear (B) using an Allen wrench

while holding the housing (A) in a vise; then
continue to turn the bevel gear (about 4-5 turns)
until the internal nut is free of the holder bolts.

KX299

4. Loosen the holder bolts, removing one; then using

a brass or copper mallet, drive the shaft out until
the notches of the retainer nut can be seen (see step
1).

KX300

5. Retighten the holder bolts and repeat steps 1 and 3

until the bevel gear can be removed from the
housing; then remove the four holding bolts.

6. Remove the bearing holder (A) using a special hex

wrench (B). Apply heat to soften the Loctite.

KX301

7. Remove the outer ball bearing (A) using a suitable

seal and bearing remover (B); then remove the
bevel gear retainer nut and the inner ball bearing.

KX302

KX303

DISASSEMBLING OUTPUT DRIVEN 
BEVEL GEAR ASSEMBLY

1. Secure the driven bevel gear assembly holding

tool (C) in a vise; then set the housing assembly
(A) on the holder, tighten nuts (D), and compress
the damping spring (E).

KX304A

2. Remove the circlip (A); then loosen and remove

the holder nuts and spring compressor.

3. Remove the spring holder (B), spring (C), cam

damper (D), and the driven bevel gear (E).

 AT THIS POINT

If no abnormal chipping or bearing roughness is
found, proceed to Installing Output Drive/Driven
Bevel Gears in this sub-section.

Содержание 2004 650























































Отзывы: