Arctic Cat 2004 650 страница 10 Скачать руководство пользователя

Страница: 10 / 54

3-10

Removing Top-Side

Components

A. Valve Covers
B. Cylinder Heads

NOTE: Remove the spark plugs and timing

inspection plug (A); then using the recoil starter,
rotate the crankshaft to top-dead-center (TDC) of
the compression stroke of the front cylinder. TF is
top-dead-center front.

KX247

ATV2057A

1. Remove the two tappet covers. Account for two

gasket rings.

2. Remove the cap screws (A) securing the front

valve cover to the head; then remove the front
valve cover (B).

ATV2065

NOTE: Leave the camshaft and camshaft chain

tensioner installed until the rear rocker case is
removed or the cam chain will have to be sup-
ported while rotating the crankshaft.

3. Rotate the crankshaft counterclockwise to position

the rear cylinder at TDC on the compression
stroke; then remove the two tappet covers.
Account for two gasket rings. TR is
top-dead-center rear.

ATV2058A

4. Remove the cap screws (A) securing the rear valve

cover to the head; then remove the rear valve
cover (B).

ATV2066

5. Remove front and rear camshaft chain tensioners

by first removing the spring cap (D). Account for
one washer (C), one spring (B), and one guide rod
(A) for each tensioner.

! CAUTION

Be sure the crankshaft is on TDC of the
compression stroke of the front cylinder or valve
damage could occur.

Содержание 2004 650























































Результаты поиска

Содержание 2004 650

Отзывы:

Похожие инструкции для 2004 650

Бренды по названию

Популярные бренды

Arctic Cat 2004 650, Руководство по обслуживанию

Результаты поиска

Содержание 2004 650

Отзывы:

Похожие инструкции для 2004 650

Бренды по названию

Популярные бренды