manualshive.com logo in svg

Arcserve UDP 8300, Руководство по установке

Поделиться
Скачать
Arcserve UDP 8300 Скачать руководство пользователя страница 4

Arcserve 

UDP

8300 and 

UDP

8400 Appliance Hardware Installation Guide   

4

3.

Electrical and General Safety Guidelines

CAUTION

This appliance is intended for installation in restricted areas only. Initial setup and maintenance 

should be performed by qualified personnel.

CAUTION

Power down the appliance following the operating system’s proper power down procedure from the front

panel. Unplug the AC power cord(s) before servicing.

CAUTION

To avoid electrical shock, check the power cords as follows:

n

This product is to be installed in Restricted Access Location only.

n

Use the exact type of power cords required.

n

Use power cord(s) that came with safety certifications. 

n

Power cord(s) must comply with AC voltage requirements in your region.

n

The power cord plug cap must have an electrical current rating that is at least 125% of the electrical current 

rating of this product. 

n

The power cord plug cap that plugs into the AC receptacle on the power supply must be an IEC 320, 

sheet C13,type female connector.

n

Plug the power cord(s) into a socket that is properly grounded before turning on the power.

CAUTION

Required operating conditions for the appliance are - 

n

Temperature: 10 to 35

o

C. 

n

Humidity, non-condensing: 8 to 90%.

CAUTION

CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1

DISPOSING OF BATTERY BACKUP UNITS - IF APPLICABLE

WARNING

If the BBU is damaged in any way, toxic chemicals may be released.

The material in the battery pack contains heavy metals that can contaminate the environment. Federal, state,

and local regulations prohibit the disposal of rechargeable batteries in public landfills. Be sure to recycle the

old battery packs properly. Comply with all applicable battery disposal and hazardous material handling laws

and regulations in the country or other jurisdiction where you are using the BBU.

WARNING

Risk of explosion if the battery is installed upside down or is replaced by an incorrect type. 

Replace it only with the same or equivalent type recommended by the manufacturer. Dispose of used 
batteries according to the instructions.

Содержание UDP 8300

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды