4
2012 series Pneudraulic Installation Tool (HK969)
Description
The
2012
models are lightweight, high-speed production
tools that install:
-04
through
-06
diameter HUCK-CLINCH
®
fasteners,
and oversize HUCK-CLINCH fasteners
-04
through
-06
diameter Huck UNIMATIC
®
blind
rivets
Any other blind fasteners
The pulling action of the pull piston is provided by a
pneumatic-hydraulic (pneudraulic) intensifier system that
is powered by 90 psi (
6.2 bar
) air pressure. The air inlet
is equipped with a connector with 1/4”-18 female pipe
threads to accept your air hose or quick-connect fitting.
MODEL FEATURE
The
2012V
model has a Slide & Tube Assembly
(P/N
124245
)—a ribbed “ON/OFF” vacuum-regulating slider
that enhances the tool capabilities by:
- expelling broken pintails into the pintail collector, and
- holding fasteners firmly in the nose assembly, with the
tool in any position.
When the tool is not in use, the OFF position (slider
forward) will prevent air loss. See Figure 9 for the
location of this assembly (pictured in the ON position) on
the tool.
Specifications
STROKE:
0.650 in (
1.65 cm
)
WEIGHT:
2012
: 4.4 lbs (
1.99 kg
)
2012B
&
2012V
: 4.7 lbs (
2.13 kg
)
MAX AIR PRESSURE:
90 psi (
6.2 bar
)
MAX FLOW RATE:
2.9 scfm
(
170 l/min
)
POWER SOURCE:
90 psi (
6.2 bar
) maximum shop air
MAX OPERATING TEMP:
125° F (
51.7° C
)
PULL CAPACITY:
2670 lbs @ 90 psi
(
11.88 kN @ 6.2 bar
)
SPEED / CYCLES:
20 per minute
HOSE KITS:
Use only genuine Huck Hose Kits rated @
10,000 psi (
689.5 bar
) working pressure.
HYDRAULIC FLUID:
Hydraulic fluid shall meet
DEXRON
®
III, DEXRON VI, MERCON
®
, Allison C-4
or equivalent Automatic Transmission Fluid (
ATF
)
specifications. Fire-resistant fluid may be used if it is
an ester-based fluid such as Quintolubric
®
HFD or
equivalent. Water-based fluid shall NOT be used as
serious damage to equipment will occur.
Sticker Locations
These stickers are located at the bottom of Cylinder Assembly 125471
and MUST be ordered and placed in these locations if they become
damaged, lost, or unreadable, or if the Cylinder is replaced.
590350
CE Sticker
590351
Max. Pressure
and Flow Sticker
590347
HUCK Address
Sticker
Figure 13
Where the following trade names are used in this manual, please
note:
DEXRON
is a registered trademark of General Motors Corporation.
Loctite
is a registered trademark of Henkel Corporation, U.S.A.
LUBRIPLATE is a registered trademark of Fiske Brothers Refining Co.
MERCON
is a registered trademark of Ford Motor Corp.
MOLYKOTE
is a registered trademark of Dow Corning Corporation
Never-Seez
is a registered trademark of Bostik, Inc.
Quintolubric
is a registered trademark of Quaker Chemical Corp.
Slic-tite
is a registered trademark of LA-CO Industries, Inc.
Spirolox
is a registered trademark of Smalley Steel Ring Company
Teflon
is a registered trademark of E. I. du Pont de Nemours and
Company.
Threadmate
is a registered trademark of Parker Intangibles LLC.
TRUARC
is a trademark of TRUARC Co. LLC.
Vibra-Tite
is a registered trademark of ND Industries, Inc. USA.
