Arai Defiant-X Скачать руководство пользователя

Страница: 9 / 12

English

TO REMOVE/REPLACE COMFORT LINING

The comfort lining is secured to the helmet by plastic bosses

①

To remove the lining, undo bosses by grasping the lining as close to each boss

as possible

②

and pulling straight up

③

. Note the fore & back, top & bottom

sides of the lining for replacement.

To wash the comfort lining, put it into lukewarm water with small amount of laundry

soap or your own shampoo and wash gently by hand. Rinse well with fresh water

and wipe off with a soft cloth. Dry it in the shade at ambient temperature.

WARNING :

Never use petrol, thinner, benzene or any other solvents.

To replace the lining, place the bosses over their plastic receptacles and push

them home

④

⑤ & ⑥.

WARNING :

When reinstalling the comfort lining, be sure the lining is

properly positioned along the inside shape of the EPS (a.k.a. Styrofoam)

liner. If the comfort lining is not properly installed, the frame of the comfort

lining may fold when you put on and take off the helmet, which may injure

your skin, etc. Whenever you feel something is wrong with the comfort

lining, check that the lining is properly installed.

①

②

③

システム内装の着脱

システム内装の外し方

①内装は四つのホックで衝撃吸収ライナの内面に取り付けられています。それ
ぞれのホックになるべく近い枠（保持プレート）を持ち、ヘルメットの中心に向
けて引っぱってホックを取り外してください。

②ヘルメット内で半球形に開いているシステム内装を折り畳んで取り出します。

Image

ホック

枠

それぞれのホックを引っぱる向き

取り出したシステム内装は、折り癖がつ

かないように広げておいてください。

システム内装の着脱

システム内装の外し方

②ヘルメット内で半球形に開いているシステム内装を折り畳んで取り出します。

Image

ホック

枠

それぞれのホックを引っぱる向き

取り出したシステム内装は、折り癖がつ

かないように広げておいてください。

システム内装の着脱

システム内装の外し方

②ヘルメット内で半球形に開いているシステム内装を折り畳んで取り出します。

Image

ホック

枠

それぞれのホックを引っぱる向き

取り出したシステム内装は、折り癖がつ

かないように広げておいてください。

⑥

⑤

④

Содержание Defiant-X













Результаты поиска

Содержание Defiant-X

Отзывы:

Похожие инструкции для Defiant-X

Бренды по названию

Популярные бренды

Arai Defiant-X, Руководство по эксплуатации

Результаты поиска

Содержание Defiant-X

Отзывы:

Похожие инструкции для Defiant-X

Бренды по названию

Популярные бренды