AR 100S1G6AB Скачать руководство пользователя страница 23

Страница: 23 / 52

Model 100S1G6AB

Rev A

2.4 REMOTE COMMUNICATIONS

This section describes remote operation of this product using the installed communications ports connected to

a remote device such as a personal computer. All ports are active at all times, however only one port may be

used at a time. Communicating through two or more ports at one time will cause data collisions and lost

commands or queries.

The

REMOTE

LOCAL

switch on the front panel allows for the amplifier to be controlled using the remote

communications ports or the front panel controls depending on its position. All remote queries will work in

either switch position. All remote commands will only work when the switch is set to

REMOTE

. When the

switch is set to

REMOTE

all front panel controls are disabled.

NOTE: Some of the following ports may not be installed on your amplifier.

2.4.1

IEEE-488 (GPIB) Communications

For IEEE-488 operation, the device address is set using the dip switches on the rear panel of the amplifier. It

is set to address 1 at the factory. If another device on the IEEE-488 bus is already using address 1, reset the

switch to a vacant address. (Resetting the address requires re-booting the unit).

Specific IEEE-488 bus commands depend on which software package you are using. To send commands be

sure that the amplifier’s address is set properly and that the controller has correctly identified the unit as a

“listening” device.

When sending commands to the unit via the GPIB interface, terminate the command with a

<LF>

, an

EOI

, or

both. The system ignores characters following the termination.

2.4.1.1

Setting the IEEE-488 (GPIB) Address

The IEEE-488 device address can be set to any number between 1 and 30. This selection is made by setting

Switches 1 to 5 of the rear panel DIP switch to the binary equivalent of the number. Table 2-1 illustrates this

switch selection. Please note that although addresses 0 and 31 can be entered, neither address is valid for this

device, and therefore should be avoided.

Table 2-1. IEEE-488 Address Selection

Device Address

Switch 1

Switch 2

Switch 3

Switch 4

Switch 5

DO NOT USE - (RESERVED FOR CONTOLLER)

on (1)

off (0)

on (1)

off (0)

on (1)

off (0)

on (1)

off (0)

on (1)

off (0)

on (1)

off (0)

on (1)

DO NOT USE

Содержание 100S1G6AB





















































Результаты поиска

Содержание 100S1G6AB

Отзывы:

Похожие инструкции для 100S1G6AB

Бренды по названию

Популярные бренды

AR 100S1G6AB, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 100S1G6AB

Отзывы:

Похожие инструкции для 100S1G6AB

Бренды по названию

Популярные бренды