AR 10051217 Скачать руководство пользователя страница 20

Страница: 20 / 90

Model 2000S1G2z8

Rev A

PS3 is a single output supply. The main +24.0 volts DC supplies voltage to the Terminal Blocks to power Fan

assemblies B1 through B68.
PS4 is a single output supply. The main +24.0 volts DC supplies voltage to the Drain FETs in the A3, A5, A6

Quad amplifiers. Voltage is also supplied to A80 Reg Assy.
PS5 is a single output supply. The main +24 volts DC supplies voltage to the Drain FETs in Quad modules

A9-16.
PS6 is a single output supply. The main +24 volts DC supplies voltage to the Drain FETs in Quad modules

A25-32.
PS7 is a single output supply. The main +24 volts DC supplies voltage to the Drain FETs in Quad modules

A33-40.
PS8 is a single output supply. The main +24 volts DC supplies voltage to the Drain FETs in Quad modules

A41-48.
PS9 is a single output supply. The main +24 volts DC supplies voltage to the Drain FETs in Quad modules

A49-56.

1.4 PROTECTION CIRCUITS

Features incorporated into this unit include RF output level protection circuits, thermal protection circuits, and

internal DC level sensing and monitoring circuits that sense the voltage on each of the final and driver amplifier

modules. There is protection for the AC main circuit. All switching supplies are short circuit protected.

Reaching a threshold of either of the RF forward (incident) or reverse (reflected) power limit adjustments,

which are adjusted to approximately 2500 watts and 1000 watts respectively, will initiate limiting, or smooth

drive level foldback, in a low-level stage of the amplifier chain. If the limiting circuits cannot keep the

amplifier’s levels below the limit threshold, the protection circuits will invoke a shutdown of the main power

supplies and low-level driver in the amplifier. Power amplifier modules are monitored for both over-current

and under-current. A reset function is provided to permit re-powering of the amplifier in case of transient or

temporary activation of the amplifier’s protection circuitry. The low-level driver and output amplifier

subassemblies are thermally monitored. The digital control panel monitors all fault signals, stores and displays

any that are invoked and asserts the required action.

1.5 INSTALLATION

Before proceeding, thoroughly inspect the amplifier for signs of physical damage that may have been incurred

during shipment and completely read the following installation and operating instructions, paying special

attention to all

CAUTION

notes.

1.5.1

Location

Select an operating location that will permit air to circulate freely around the amplifier’s cabinet. The

Model 2000S1G2z8 utilizes air cooling and should be located where the normal flow of air into or exiting from

the unit will not be restricted, diverted, or re-circulated through the unit itself; in particular, the flow of warm

air exiting the rear of the amplifier should not be impeded.

Do not position the unit next to a wall or other equipment that would restrict the flow of air into the bottom of

the unit or out of the rear of the unit. The air intake is through the front, left side, and right side of the amplifier’s

perforated side panels. Ample space–greater than 20 inches (50 cm), should be available on either side for

proper cooling, 40 inches (1m) or greater should be available for the front and rear of the amplifier.

Содержание 10051217



























































































Результаты поиска

Содержание 10051217

Отзывы:

Бренды по названию

Популярные бренды

AR 10051217, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 10051217

Отзывы:

Бренды по названию

Популярные бренды