Aquion EFP10, Инструкция по установке и эксплуатации

Страница: 5 / 12

INSTALLATION
Page 5
EN - English
WATER SUPPLY ADAPTOR

An adaptor is supplied with the water filtration system
for the connection to the water supply inside the house; at
the inlet side (connection to the plumbing inside the house)
it has a 3/8” BSP female thread; the corresponding thread
on the plumbing inside the house should be 3/8” BSP male.

For filter cartridge replacement, the water supply to the
water filtration system needs to be turned off; therefore it
is recommended to install the water supply adaptor behind
a stop valve. Typically this can be the stop valve that is
already in place to shut off the cold water supply to the
main faucet. If the water supply adaptor can not be
installed after this stop valve, we strongly recommend to
install a separate stop valve (not included with this
product!), preferably with 3/8” BSP male thread at the
outlet.

Make sure to shut off the water supply to the place of
installation, before you start any plumbing work.
AFTER EXISTING STOP VALVE IN COLD WATER SUPPLY TO
MAIN FAUCET
1.
Remove the existing connection coming from the main
faucet from the outlet of the stop valve.
2. Install an appropriate T-adaptor (preferably with 3/8”
BSP male thread, for connection of the water supply
adaptor) at the outlet of the stop valve.
3. Reinstall the connection coming from the main faucet to
one of the outlets of the T-adaptor.
4. Screw the water supply adaptor onto the other outlet of
the T-adaptor; make sure the gasket is installed inside
the female thread of the water supply adaptor. Tighten
the water supply adaptor.
WITH SEPARATE STOP VALVE (not included)
1.
Install an appropriate stop valve in the cold water line
underneath the sink, preferably with 3/8” BSP male
thread at the outlet.
2. Screw the water supply adaptor onto the outlet of the
stop valve; make sure the gasket is installed inside the
female thread of the water supply adaptor. Tighten the
water supply adaptor.
FILTER HOUSING UNIT

Mount the filter housing unit in vertical position.

Fix the filter housing unit against a solid surface only
(f.e. wooden wall of kitchen cabinet), using suitable
mounting screws (not included with this product!).

Make sure to leave minimum 30 mm clearance below
the filter housing unit, to allow for easy removal of the
filter sump during filter cartridge replacement.

Make sure to leave minimum 75 mm clearance at
either side of the filter housing unit, to allow for easy
tubing connections.

The filter housing unit has an integrated mouting
bracket at both sides, so it may be rotated 180° depending
on the optimal setup of the inlet (supply of untreated
water) and outlet (to filtered water faucet) at the specific
place of installation.
1. Select an appropriate location under the sink for the
installation of the filter housing unit.
2. Mark the location of the mounting screw(s) (1x for single
sump models, 2x for double sump models).
3. Install the mounting screw(s).
4. Install the filter housing unit.
5. Tighten the mounting screw(s).
FAUCET

Install the faucet on a flat surface to assure secure
installation and adequate sealing between the faucet and
the counter top.

Use the appropriate tools (drilling machine, drill bit)
and procedures to make the hole in the counter top.
Contact a professional if necessary, to avoid damage to the
counter top.

Make sure the faucet does not hinder the correct
functioning of any other ‘device’ on top of the counter top
(f.e. main faucet, window,…)

Make sure to leave minimum 100 mm clearance under
the counter top, to allow for easy installation of the faucet.

Refer to the assembly diagram included with the faucet
for correct assembly of the faucet.
1.
Select an appropriate location for the installation of the
faucet.
2. Drill a hole (with diameter of min. 12 mm – max. 15 mm)
in the counter top.
3. Lower the faucet body through the hole in the counter
top; make sure the o-ring is properly installed in the
faucets base.
4. From underneath the counter top, install the washers
and locking nut over the threaded stud of the faucet
body; tighten the locking nut.
5. Screw the faucet’s spout onto the faucets body.