background image

Aquatic 5

LuxeAir Series Owner's Manual & Installation Guide

SAFETY INSTRUCTIONS

 

WARNING:

 WHEN USING THIS UNIT, THESE BASIC PRECAUTIONS SHOULD BE FOLLOWED.

This manual contains information and instructions for proper operation and maintenance of your whirlpool. Failure to  

follow these instructions could result in personal injury, electrical shock or fire.

READ AND FOLLOW ALL INSTRUCTIONS

DANGER! TO REDUCE THE RISK OF INJURY:

A.  Do not permit children to use this unit unless they are closely supervised by an adult at all times. Supervision is 

also required when whirlpool bath is used by an elderly or handicapped individual.

B.  Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by 

the manufacturer.

C.  Do not operate this unit without guard over the suction fitting.

D.  The water in a whirlpool should never exceed 40°C (104°F). Water temperatures between 38°C (100°F) and 

40°C (104°F) are considered safe for a healthy adult. Use time should be limited to approximately 30 minutes, 

followed by a shower to cool down. Longer exposures may result in hyperthermia. The symptoms of this condition 

are nausea, dizziness and fainting, which can be fatal. Lower water temperatures are recommended for 

extended use (exceeding 10 - 15 minutes) and for young children.

E.  Since excessive water temperatures have a high potential for causing fetal damage during the early months of 

pregnancy, pregnant or possibly pregnant women should limit whirlpool water temperatures to 38°C (100°F).

F.  The use of drugs or alcoholic beverages before or during whirlpool use may lead to unconsciousness with the 

possibility of drowning. Never use the whirlpool while under the influence of alcohol, anticoagulants, stimulants, 

antihistamines, vasoconstrictors, vasodilators, hypnotics, narcotics or tranquilizers.

G.  Persons with a medical history of heart disease, low or high blood pressure, circulatory system problems, or 

diabetes should consult a physician before using a whirlpool.

H.  Persons using medication should consult a physician before using a whirlpool since medication may induce 

drowsiness while other medication may affect heart rate, blood pressure and circulation.

DANGER:

 To reduce the risk of injury, enter and exit the bath slowly.

WARNING:

 Never operate electrical devices in or near the bath. Never drop or insert any object into any opening 

within the whirlpool.

This unit must be connected to a supply circuit that is protected by a Ground Fault Circuit Interrupter (GFCI). Such a  

device should be installed by a licensed electrician and should be tested on a regular basis (at least monthly). To test  

the GFCI push the 

TEST

 button. The GFCI should interrupt the power. Push the 

RESET

 button and the power should  

be restored. If the GFCI fails to operate in this manner there is the possibility of an electric shock. 

DO NOT USE.

  

Disconnect the unit and have the problem corrected by a qualified service technician. To avoid the possibility of  

personal injury and discoloration of the acrylic surface, the inlet water temperature should not exceed 60°C (140°F).  

The bath should be drained after each use. Each bather should start their bath with fresh water.

CAUTION:

 do not use harsh abrasives or solvents for cleaning this unit.

INSTALLER/OWNER BEARS ALL RESPONSIBILITY TO COMPLY WITH ALL STATE AND LOCAL CODES WHEN  

INSTALLING THIS PRODUCT.

SAVE THESE INSTRUCTIONS

Содержание LuxeAir Series

































Отзывы: