background image

Water Coming from the Heat Pump..

.

Is it a leak or just condensation from normal operation?  

Here’s how to find out.

Test the water draining out the heater base for the presence of the sanitizer 

being used in the pool or spa. Using a water test kit, or a test strip, check a 

sample of the water for chlorine or bromine. If the sample tests positive for 

sanitizer, call Aquatherm for service at: 239-482-0606. If the test is negative, 

the water is probably harmless condensation.

Or, as an alternate method, shut the heat pump off, leaving the circulation 

pump running. Within a few hours, there should be a marked reduction in 

the amount of water seen around the bottom of the heat pump. If the water 

appears to be drying up, the water is probably harmless condensation, indica-

tive of normal operation.

NOTE:

  The water test method will not be effective if an ionizer or ozone gen-

erator is being used to produce the sanitizing agent.

CAUTION! 

  If after testing, a water leak is suspected, 

immediately

 shut OFF 

the water pump and  contact Aquatherm Customer Support: 239-482-0606.

SAFETY INFORMATION

Used and maintained properly, your heat pump will provide years of safe and 

economical service. However, as with any mechanical or electrical device, 

to get the most from your heat pump–while insuring personal safety for you 

and others–certain operational and maintenance factors must be observed.  

Except for a few minor owner-capable maintenance items (explained later in 

this manual), repair and service of your heat pump must be performed only by 

licensed service personnel. If you suspect your heat pump is not performing 

properly, refer to the Troubleshooting section in this manual to determine if  

service is required. Your installer can be one source of service, or you can call 

Aquatherm at (239) 482-0606 or 888-297-3826.  For questions concerning 

installation, modifications, operation, service and upkeep, please contact your 

installer or Aquatherm Customer Support. 

WARRANTY MAY BE VOIDED IF THE HEATER HAS BEEN 

USED, MAINTAINED, OR REPAIRED IMPROPERLY.

In addition to voiding the manufacturer’s warranty, unapproved installation 

methods, nonstandard modifications, poor or incorrect maintenance, service 

by unqualified personnel, or improper use of the heater may result in personal 

injury and/or property damage. For personal safety, and to avoid damage to 

equipment, follow all safety instructions displayed on the heat pump and 

within this manual.

15

CONTENTS

Model/Serial # ....................................................................Cover
Heat Pump Options ....................................................................1
How A Heat Pump Works ..........................................................1
Heating Quick Start & Stop ................................................. 2 - 3
Heater Controls ..........................................................................4
Operational & Programming Codes ...........................................5
Operational & Maintenance Recommendations ........................6
Maintenance & Operation .................................................... 7 - 8
  Proper Water Flow
  Water Chemistry Standards
  Pool & Spa Refinishing
  Irrigation and Storm Run-Off
  Proper Clearances
Heating Tips ...............................................................................9
Seasonal Use & Shut Down .....................................................10
Freeze Protection .....................................................................10
Recommended Maintenance ....................................................11
Troubleshooting ............................................................... 12 - 13
Safety Information ...................................................................13
Aquatherm Contact Information ...............................Back Cover

i

Содержание AT115











Отзывы: