manualshive.com logo in svg

AQUALEAK 10K, Инструкция по установке и эксплуатации

Поделиться
Скачать
AQUALEAK 10K Скачать руководство пользователя страница 9

10K manual 

 

 

 

 

Issue 1.0, 31st July 2019 

 

Page 9 

The two blocks of DIP switches on the 10K’

s front panel are used for configuration. DIP SW1 

configures parameters such as leak and contamination thresholds, latching alarms, and re-
alarm time interval. DIP SW2 is used to set the Modbus address information for the 10K. 

The 10K also provides configuration capability and status information to a Modbus equipped 
system via its EIA-485 port. 

 

 

1  Four-character LED display 

4  DIP switch SW2 

–

 Modbus Configuration 

2 

LED’s

 

5  Test/Reset/Alarm/Silence push-button 

3  DIP Switch SW1 

–

 Configuration Settings 

Figure 2  Aqualeak 10K controls and indicators 

Internal description 

Please refer to Figure 3. The active components of the Aqualeak 10K are the 10K Controller 
and the associated Power Supply Unit (PSU). They are mounted on a standard DIN rail inside 
the back box of the 10K casing. To the left of the PSU are DIN rail mounted terminal blocks 
for the mains supply live, neutral and Earth connections. 

The 10K Controller contains two circuit boards. The top circuit board houses the operational 
controls and displays. The lower circuit board houses connectors for the leak detection sensor 
cable, relay outputs, communications and AC/DC power, and Earth. 

If the 10K requires repair and service, it must be either returned to Aqualeak, or an Aqualeak 
Installation Engineer called-out. 

SUPPLIED ITEMS 

The Aqualeak 10K, as supplied, comprises the following items. Before installing the 10K, 
check that all items are present and undamaged: 

1.

 

The 10K unit, shown on the front cover of this manual. 

2.

 

A 4.57 m leader cable, that is used to connect the sensor cable to the Aqualeak 10K. 

3.

 

An End Of Line (EOL) terminator. 

Содержание 10K






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды