AQUALEAK 10K Скачать руководство пользователя страница 27

Страница: 27 / 37

10K manual

Issue 1.0, 31st July 2019

Page 27

Register Name

Description

Units

Range

40004

Latched Alarms

(read-only)

Latched alarm requires

Aqualeak 10K to be reset
once alarm is cleared.

Note

: Set with DIP SW1;

this register is read-only.

0 = Disabled
1 = Enabled

Default: Disabled

0-65535

40005

Silence Audible

Alarm

Indicates whether or not

the audible alarm sounds
when the Aqualeak 10K

goes into alarm state

0 = Disabled

1 = Enabled

Default: Disabled

0-65535

40006

Reset Alarm

Resets the Aqualeak 10K

after an alarm state.
Alternatively, press and

hold the front panel’s

Test/Reset button for 3
seconds.

0 = Disabled (do not

reset alarm)
1 = Enabled (reset

alarm)

Default: 0 (Disabled)

0-65535

40007

Sample Size

Number of samples taken

to calculate the leak

location

0 = Set to default value
4 = Minimum
25 = Maximum

Default: 12

0-65535

40008

Resistance per

Foot

Milliohms of resistance of

installed leak detection

cable.
This value is set here and

can also be read through
register 30008.

2000

–

3500 milliOhms/

foot
or
3500

–

4240 milliOhms/

foot*
*to convert this value

to Ohms/foot, divide

the number by 1000

0-65535

40009

AC Rejection

Frequency

Used by ADC to reject AC

powerline frequencies.
Needed only if the

Aqualeak10K is running on
24 VAC power.

0 = 60Hz
1 = 50Hz
Default: 1 (50Hz)

0-65535

40010

Spare

Not used.

0-65535

40011

Spare

Not used.

0-65535

40012

Spare

Not used.

0-65535

40013

Spare

Not used.

0-65535

40014

Spare

Not used.

0-65535

40015

Spare

Not used.

0-65535

40016

Leak Alarm Delay Amount of time that

passes between leak

detection and alarm
notification.

–

990 seconds

Default: 10 seconds

0-65535

40017

Contamination

Alarm Delay

Amount of time that

passes between cable

contamination detection

and alarm notification.

–

990 seconds

Default: 120 seconds

0-65535

Содержание 10K






































Результаты поиска

Содержание 10K

Отзывы:

Похожие инструкции для 10K

Бренды по названию

Популярные бренды

AQUALEAK 10K, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 10K

Отзывы:

Похожие инструкции для 10K

Бренды по названию

Популярные бренды