background image

RACING:

Your Revolt was designed to fi t into boat IMPBA and NAMBA P class racing. What you will fi nd is power systems designed for this 
boat and others like it making their own class called P-Spec. This boat fi ts into the P-Spec Mono racing class. Check the websites 
listed below for information and places to race your Revolt.

NATIONAL ORGANZATIONS AND ONLINE HELP:

www.impba.net

www.namba.com

www.ampba.asn.au 

www.aquacraftmodels.com

www.inltlwaters.com

www.rcgroups.com

www.rcuniverse.com

ORDERING REPLACMENT PARTS:

 

AQUB6236

AQUB6237

AQUB6238

AQUB6239

AQUB7759

AQUB7910

AQUB8002

AQUB8003

AQUB8753

AQUB8754

AQUB8755

AQUB8756

AQUB8757

FRP Cowl Blue 

FRP Cowl Red 

FRP Cowl Silver 

FRP Cowl White 

4mm Stainless Steel Prop Nut

Motor Mount 

.150" Flex Drive Cable

.187" Prop Shaft Bushing

Rudder Blade

Rudder Bracket 

Rudder Blade Mount 

Rudder Control Arm

Rudder Back Plate Mount 

AQUB8758

AQUB8782

AQUB8808

AQUB8810

AQUB8811

AQUB9004

AQUB9541

AQUB9542

AQUB9543

AQUB9544

AQUB9545

AQUB9547

Rudder Linkage 

Servo Mount 40mm

Strut  25"-35" Hulls

Strut Mounting Brackets 

Strut Back Plate Mount 

Low-Friction Cable Liner

GrimRacer CF Trim Plates 

GrimRacer Rudder Assembly 

GrimRacer Mono Strut 

GrimRacer Mono Turn Fin

GrimRacer Motor Coupler 5mm-.150"

.187" Drive Dog

AQUB24-25Mnl

© 2012 Hobbico, Inc. All rights reserved.

Содержание Revolt 30













Отзывы: