AquaCraft GP-1 Ulta Скачать руководство пользователя страница 7

7

Performance Tuning

Keep in mind, as you tune your GP-1 Ultra Mini Hydroplane for 
top speed and handling that this boat IS SMALL AND FAST! 
Because of its size it only needs very small adjustments to 
change the way it performs.

STEERING DEFLECTION

Your GP-1 Ultra Mini Hydroplane has VERY aggressive steering. 

It’s important to keep this in mind as you tune your boat. The 
rudder only needs a small amount of defl ection to turn well. 
Setting the rate knob to high (Clockwise) can upset the handling. 
Ultimately, it needs to be tuned to your race course or liking.

SHARPENING

It’s best to sharpen the turn fi n to a razor-sharp edge. This will 
eliminate drag and reduce lift. Remember as a rule of thumb, 
if it touches the water, it needs to be sharp or have sharp 
edges. GRIMRACER SAYS! Sharpen the outer edge of the 
turn fi n toward the inside of the boat. This is a great way to 
help control prop torque.

STRUT

The strut can be 

tweaked

 to change the ride of the boat but 

only experienced modelers should attempt this. If you are going 
to 

tweak

 the strut remove the prop shaft and prop. Loosen the 

strut bolt. Move or adjust the strut, taking care not to lose the 

alignment of the driveshaft to the motor coupler. If needed, 
you might have to re-bend this area to regain alignment.

Racing

Roostertail

Corner

Aquacraft Point

Turn

GrimRacer

Turn

150 ft

30 ft

Start/Finish

Drivers

GP-1 ULTRA MINI HYDROPLANE RACING RULES

Boats must remain stock. Only hardware adjustments are 
allowed. Sharpening and scuffi ng are legal, but changing 
a prop is not. You are also allowed to paint or add decals if 
you choose.

A heat race is 6 laps and typically consists of up to 6 boats 

per heat. You can run as many heats per event as you like, 
but 3 to 5 is typical.

To start a race, set a timer to 30 seconds. Launch the boats 

and make one full clockwise lap. At the end of the lap, you 
need to be on the right side of the start line and going full 
speed. Being over the start line at the end of the 30 seconds 
puts you in last place. Be careful not to “jump the start.”

Cutting inside a buoy AT ANY TIME will incur a 50 point 

penalty per buoy.

Points structure goes like this.

1

st

 place (per heat) 400 pts

2

nd

 place 300 pts

3

rd

 place 225 pts

4

th

 place 169 pts

5

th

 place 125 pts

6

th

 place 96 pts

In fi ve rounds you have the potential to acquire up to 2,000 pts.

Good luck and good racing. Remember to 

place your racing pictures and videos on the 

AquaCraft Facebook page!

AQUB1820 GP-1 Mini.indd   7

AQUB1820 GP-1 Mini.indd   7

5/22/2013   1:22:54 PM

5/22/2013   1:22:54 PM

Содержание GP-1 Ulta









Отзывы: