Aquacal TropiCool TC1000 Скачать руководство пользователя страница 20

Страница: 20 / 35

Page - 17

1.5.f Schematics

Schematics are located on the inside of the equipment access panel.

PLEASE NOTE:

Specifications are subject to change without notice.

Schematics are available by calling AquaCal

Customer Support.

See "Contacting

AquaCal AutoPilot, Inc." on page 1.

Please have the complete model and serial number available.

See "Identifying Model Specifications" on page 25.

1.5.g Connecting an External Controller

To support a direct connection to an external controller, AquaCal

chillers are equipped with optional terminal

blocks. These terminals are on the microprocessor located on the low-voltage side of the electrical enclosure.

WARNING

Failure to heed the following may result in injury or death.

This section is only for qualified installers who are familiar with swimming pool and spa safety standards.

The installer must be familiar with service industry techniques.

Deactivate power while routing wiring to control board.

NOTICE

Failure to heed the following may result in damage to equipment.

The wire size connecting the controller must be 16-gauge, 2-conductor or larger, low-voltage wire.

Use direct connection (

dry contact)

provided on the microprocessor for external controllers

Dry Contact Connection Points to the

Microprocessor

Please confirm the type of external controller to be installed
and follow the appropriate instructions.

two-wire

controller

(with an internal thermostat)

The

user can set and adjust the temperature at the controller's
screen.

three-wire

controller

(with an "OFF" position

The

user adjusts the temperature at the heat pump. The user
can select pool or spa mode or turn off the heat pump using
the controller.

three-wire

controller (

without an "OFF" position

The user adjusts the temperature at the heat pump. The
user can select pool or spa mode, but must turn off the heat
pump at the heat pump display panel.

Содержание TropiCool TC1000




































Результаты поиска

Содержание TropiCool TC1000

Отзывы:

Похожие инструкции для TropiCool TC1000

Бренды по названию

Популярные бренды

Aquacal TropiCool TC1000, Руководство по установке

Результаты поиска

Содержание TropiCool TC1000

Отзывы:

Похожие инструкции для TropiCool TC1000

Бренды по названию

Популярные бренды