9
ROUTINE MAINTENANCE
TIPS:
• Backwash and rinse filter and clear weir and pump basket before operating your new SPLASHER pool cleaner.
• Backwashing and cleaning the weir and pump baskets should be done weekly.
• When replacing the diaphragm or any part of your SPLASHER it is advised that you let your local pool dealer replace it
for you. This is due to the complexity of the replacement.
• Do not leave the SPLASHER or hoses in direct sunlight for extended periods when out of the water.
1. Place the diaphragm inlet plate over the correct end of the SPLASHER diaphragm. Ensure the ring is
properly secured into the locating grooves of the diaphragm. The flat side of the inlet plat must show up,
the rib side must show to the bottom as in picture 1.
2. Insert the cleaner’s inner tube into the diaphragm on the end opposite the inlet plate. (picture 2)
3. Place the cartridge over the top of the inner tube with the larger opening to the diaphragm and inlet
plate. Slide the cartridge down over the inner tube and ensure the inlet plate is properly secured into the
cartridge. Note: Ensure the diaphragm is not twisted once installed into the cartridge (picture 3)
4. Insert the diaphragm, inlet plate and inner tube assembly into the main body and ensure the diaphragm
cartridge is pushed fully into the main body. The diaphragm is assembled ready for the remaining
SPLASHER components to be assembled.
Debris:
Keep your skimmer basket, pump strainer basket, skim filter, sand filter, cartridge filter (as applicable)
free of debris. To ensure maximum suction and cleaner efficiency, backwash your filter at regular intervals.
Remember that the SPLASHER is driven by water flow and that a dirty filter will reduce the water flow through
the SPLASHER and will affect the SPLASHER’s operation. If the filter is clean and the water flow paths to and
from the filter are clear, your water flow rate could be too high and the flow control valve should be adjusted
to reduce the water flow rate to achieve good pool sweeper action.
Cleaning:
Keep your SPLASHER clean and free of algae by washing with a mild detergent. Do not expose
SPLASHER to harsh chemicals.
Wear and tear:
Ensure that the SPLASHER’s disc, foot pad, deflector wheel and diaphragm are in good
condition. As the disc wears, it will become shiny and very smooth. Under extreme wear conditions the disc
will also start to warp and tear. The disc should then be replaced. The foot pad will also become shiny and
very smooth which will reduce its ability to adhere to the pool surface. The foot pad should then be replaced.
The deflector wheel will wear as it comes into contact with pool edges, such as the walls or steps. Wearing
is likely to occur in specific spots. The diaphragm should be inspected regularly and when stretched or torn
must be replaced.
Hoses:
Your hoses should be flexible and straight. If your hoses have become brittle they should be replaced
and, if not straight, place them in straight positions in the direct sun light for a few hours. Your hoses should
be without leaks and should always be securely connected. They may rub against the wall and if so, a hose
protector may be used.
Chemical use and your SPLASHER:
The harsh effects of chemicals in pool water could affect the coloring of
your SPLASHER. This will however not affect the performance and cleaning ability of the SPLASHER. In order
to minimize damage and discolouration, it is recommended that your pool is kept at the correct alkalinity and
pH (please see below). The SPLASHER should also be removed from the pool for a minimum of 4 hours when
‘shock’ treatment is employed.
Ideal water conditions for the SPLASHER are:
Fiberglass Pools
Marbelite Pools
Total Alkalinity
120 - 150ppm
80 - 120ppm
pH Levels
7.0 - 7.2
7.2 - 7.6
Chlorine
1.0 - 1.5ppm
1.0 - 1.5ppm
