Aqua MAX CF26 series Скачать руководство пользователя страница 6

ABOUT YOUR WATER HEATER 

 WARNING 

This water heater is only intended to be operated by persons who have the experience or the knowledge and 
the capabilities to do so. This water heater is not intended to be operated by persons with reduced physical, 
sensory or mental capabilities i.e. the infirm, or by children. Children should be supervised to ensure they do 
not interfere with the water heater. 
 
The water heater uses 240 Volt AC electrical power for operation of the control systems and the combustion 
fan. The removal of the front panel will expose 240 V wiring. It must only be removed by a qualified person. 
 
The power lead from the water heater must be plugged into a weatherproof electrical outlet. Take care not to 
touch the power plug with wet hands. 
 

SAFETY 

This  water  heater  is  supplied  with  temperature  sensors,  a  FlameSafe

®

  protection  system  and  a  pressure 

relief valve. These devices must not be tampered with or removed. The water heater must not be  operated 
unless each of these devices is fitted and is in working order. 
 
If the power supply cord or plug is damaged, it must be replaced by a qualified person in order to avoid a 
hazard. The power supply cord and plug must be replaced with a genuine replacement part available from 
Aquamax. Phone Aquamax Service to arrange for an inspection. 
 

 

Warning:

  For  continued  safety  of  this  water  heater  it  must  be  installed,  operated  and  maintained  in 

accordance with the Owner‟s Guide and Installation Instructions. 
 

The Aquamax warranty may not cover faults if relief valves or other safety devices are tampered with 
or if the installation is not in accordance with these instructions. 

 

 

Do  not  store 

flammable  or  combustible  materials

  near 

the  water  heater.  Flammable  liquids  (such  as  petrol), 
newspapers  and  similar  articles  must  be  kept  well  away 
from the water heater and the flue terminal. 

 

Do  not  use 

aerosols,  stain  removers  and  household 

chemicals

 near the water heater whilst it is working. Gases 

from  some  aerosol  sprays,  stain  removers  and  household 
chemicals become corrosive when drawn into a flame. 

 

Do  not  store 

swimming  pool  chemicals,  household 

cleaners,

 etc., near the water heater. 

 

Do  not  place  anything  on  top  of  the  water  heater  or  in 
contact with the flue terminal. Ensure the flue terminal is not 
obstructed in any way at any time. 

 

Do not use Propane / Butane gas mixtures in a Propane model. A Propane model is designed to operate 
on  Propane  only.  The  use  of  Propane / Butane  mixture,  such  as  automotive  LPG  fuel,  in  a  Propane 
model is unsafe and can cause damage to the water heater. 

 

PRECAUTIONS 

Where  damage  to  property  can  occur  in  the  event  of  the  water  heater  leaking,  the  water  heater  must  be 
installed  over  a  safe  tray.  Construction,  installation  and  draining  of  a  safe  tray  must  comply  with 
AS/NZS 3500.4 and all local codes and regulatory authority requirements. 
 
The  water  heater  must  be  maintained  in  accordance  with  the  Owner‟s  Guide  and  Installation  Instructions. 
Refer to 

“General Maintenance”

 on page 7, 

“Minor Six Month Maintenance”

 on page 7 and 

“Major Five Year 

Service”

 on page 7. 

 
If this water heater is to be used where an uninterrupted hot water supply is necessary for your application or 
business  you  should  ensure  that  you  have  back  up  redundancy  within  the  hot  water  system  design.  This 
should  ensure  the  continuity  of  hot  water  supply  in  the  event  that  this  water  heater  were  to  become 
inoperable for any reason. We recommend you seek advice from your plumber or specifier about your needs 
and building back up redundancy into your hot water supply system. 

 

 

Содержание CF26 series

























































Отзывы: