manualshive.com logo in svg

Aqua Lung EA-3000 LW, Техническое руководство

Поделиться
Скачать
Aqua Lung EA-3000 LW Скачать руководство пользователя страница 18

18   

SEA-3000 LW & SEA-4500 Technical Manual

15.

 Refit the hose (38) onto the second stage and tighten the 

hose nut by hand until it stops. DO NOT use any tools to tighten 

the hose nut onto the inlet fitting (55). Audible clicks should 

be heard as the hose nut is tightened into place. Check the 

hose nut is locked into place and cannot be loosened without 

squeezing the locking slide ring (58).

NOTE: The mouthpiece can be adjusted to several 

different user preferred positions.

 (Reference the 

User's Manual for more information).

13.

 Install the retainer ring (45) into the box bottom (59). 

Insert the pin spanner on the 5 in 1 tool into the slots of 

the retainer ring and screw it into the box bottom hand-

tight. Ensure the front cover (46) slots have remained in 

a horizontal position. Screw the purge cover (44) onto the 

box bottom until hand-tight.

14.

  Install the mouthpiece (61) onto the box bottom (59). 

Loosely fasten a strap clamp (60) into the groove at the base 

of the mouthpiece with the tab on the MP hose side. Pull the 

strap clamp tight and trim the excess strap flush with the tab 

using diagonal pliers.

Содержание EA-3000 LW

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды