manualshive.com logo in svg

Aqua Lung EA-3000 LW, Техническое руководство

Поделиться
Скачать
Aqua Lung EA-3000 LW Скачать руководство пользователя страница 16

16   

SEA-3000 LW & SEA-4500 Technical Manual

Second Stage Reassembly 

2.

 Use your fingers to screw 

the exhaust cover (64) onto 

the box bottom (59) until 

hand-tight. 

3.

 Install o-ring (51) onto the spring carrier (50). Insert the 

spring carrier into one end of the spring (52) and the shuttle 

valve (53) into the other. Carefully guide the end of the spring 

carrier into the spindle body (49).

WARNING:

 

Flooding of the second stage may occur 

if the exhaust valve is folded under or the barb on 

the stem is not pulled through the hole in the exhaust 

port all the way. 

NOTE:  Look into the open end of the spindle body to 

ensure the legs of the lever are positioned in front of the 

shuttle valve. This retains the shuttle valve inside the 

spindle body. Check that the lever has a full range of 

movement and does not catch on the spindle body.

CAUTION:

 Ensure the legs of the lever are parallel  to 

each other and not bent. If necessary, gently squeeze 

the legs together to straighten.

Correct

Incorrect

1.

 Install the exhaust valve (63) into the box bottom (59) by 

inserting the stem through the center hole of the exhaust port. 

Pull the stem through until the barb is on the opposite side of 

the hole in the exhaust port. Examine the flap of the exhaust 

valve to make sure it is laying flat and is not distorted or folded 

under. Use a pair of small diagonal pliers to trim the stem so 

it is only about 1/4" long.

Visible 

Gap

Center Hole 

(on Top)

5.

 Carefully insert the MP 

seat (54) into the shuttle 

valve (53). Make sure the 

MP seat is positioned 

correctly and flush with 

the end.

4.

 Position the spindle body (49) with the threaded end to the 

left and small center hole on top. Using your finger, press in 

on the shuttle valve (53) to fully compress the spring (52).

The shuttle valve should pass the lever holes in the spindle 

body, creating a small visible gap. Insert the feet of the le-

ver (48) one leg at a time into the lever holes, in front of the 

shuttle valve.

CAUTION:

 Use the end of your finger to insert the 

new MP seat into the shuttle valve. Make sure it sits 

flush with the end and the seat does not get scratched 

during installation. Damage to the seat will cause the 

second stage to leak when fully assembled.

Содержание EA-3000 LW

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды