background image

SAFETY PRECAUTIONS

Before installing and operating this equipment be sure everyone involved in its operation is fully trained and

is aware of all precautions. Accidents and problems can result by a failure to follow fundamental rules and

precautions.

The following words and symbols, found in this manual, alert you to hazards to the operator, service

personnel or the equipment. The words are defined as follows.

!

!

WARNING:

This symbol refers to a potential hazard or unsafe practice, which could result

in serious injury or death.

!

!

DANGER:

This symbol warns of imminent hazard which will result in serious injury or

death.

!

!

CAUTION:

This symbol refers to a potential hazard or unsafe practice, which may result in

minor or moderate injury or product or property damage.

!

!

NOTICE:

This symbol refers to information that needs special attention or must be fully

understood even though not dangerous.

SPECIFICATIONS AND DIMENSIONS

Model

Width

Depth

Height

No. of

kW Per

Total

in. (mm)

in. (mm)

in. (mm)

Elements

Element

kW

Griddle Surface Dimensions: Model

Width in./cm

Depth in./cm

General Installation Instructions:

Caution:

DO NOT

NOTICE:

NOTICE:

EGD-48

49.0/125

29.5/75

0.31/0.8

8

2.7

21.6

EGD-72

72.0/191

29.5/75

0.31/0.8

12

2.7

32.4

EGD-72

72.0/191

32.5/83

0.31/0.8

12

2.7

32.4

Double Trough

EGD-48

46.5/119

23.94/61

EGD-72

69.5/177

23.94/61

use an open flame to check for leaks. Check all gas piping for leaks with a

soap and water solution before operating unit.

THE UNIT, WHEN INSTALLED, MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE

WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL ELECTRICAL

CODE,ANSI/NFPA70, LATEST EDITION.

CANADIAN INSTALLATION MUST COMPLY WITH THE CANADIAN ELECTRICAL CODE, CSA C22.2,

ASAPPLICABLE.

Local codes regarding installation vary greatly from one area to another. The National Fire

Protection Association, Inc., states in its NFPA 96 latest edition that local codes are "authority having

jurisdiction" when it comes to requirements for installation of equipment. Therefore, installations should

comply with all local codes.

3

Содержание EGD-48













Отзывы: