APRILIA SCARABEO 50 -, Книга по эксплуатации и обслуживанию

Страница: 65 / 104

65
use and maintenance Scarabeo 50
-
their seats, and brake fluid will be
spilled. Should you accidentally do
this, take your vehicle to your Local
APRILIA
Dealer who will know how to re-
pair this damage.
◆
Move the front wheel forward until you
can withdraw the disc from the brake cal-
iper (7).
◆
Without removing the brake caliper, ro-
tate the left fork leg (8) clockwise, in such
a way as to create the space necessary
to withdraw the wheel.
◆
Remove the wheel completely by pulling
it forward.
◆
Disconnect the speedometer drive (5).
REASSEMBLY
Carefully read p. 55 (MAINTENANCE).
◆
Apply a thin film of lubricating grease,
see p. 98 (LUBRICANT CHART) to the:
– inside of the speedometer drive(5);
– outer seats of the wheel hub;
– front axle (4).
◆
Position the wheel on the support (2) be-
tween the fork legs.
◆
Position the tang (9) of the speedometer
drive (5) in the appropriate seat on the
wheel hub.
a
CAUTION
While reassembling the wheel, be care-
ful not to damage the brake line, the
disc and the pads.
NOTE
The slot (10) in the brake caliper
(7) must be located in the lug (11) on the
inside of the left fork leg.
◆
Insert the wheel between the fork legs,
carefully introducing the disc into the brake
caliper.
a
WARNING
Danger of injury.
Keep your fingers clear. Do not attempt
to line up the wheel and the axle clamps
with your fingers.
◆
Move the wheel around until the axle
hole and the axle clamps are aligned.
◆
Insert the washer (6) between the speed-
ometer drive (5) and the fork right rod.
◆
Push in the axle (4) completely and tight-
en it to its appropriate tightening torque.
Axle (4) tightening torque:
36.17 ftlb (50 Nm).
◆
Remove the support (2) from under the
tire.
◆
Remove the support (1) from under the
vehicle.
◆
Retract the center stand.
◆
Apply the front brake lever, and then
push down on the handlebars, com-
pressing the fork springs several times.
This will align the fork tubes.
◆
Place the vehicle on the center stand,
see p. 53 (PLACING THE VEHICLE ON
THE STAND).
◆
Tighten the axle clamp screw (3).
Screw (3) tightening torque:
8.68 ftlb (12 Nm).
◆
Ensure that the following components
are neither dirty nor oily:
– tire;
– wheel;
– brake disc.
a
WARNING
After servicing the brakes, always
check them for function. If the stroke of
the lever is excessive, or if you detect
that the effectiveness of the brakes is
reduced in any way, have your vehicle
serviced by your Local
APRILIA
Dealer.
It may be necessary to have your dealer
bleed the system, or there may be some
other problem with the brake system.
Never ride your vehicle in traffic immedi-
ately after servicing the brakes. Always
apply the brake lever several times be-
fore riding your vehicle. Then, try your
vehicle in a parking lot or other safe area
with little traffic to ensure that the brakes
are working properly. Failure to observe
this warning can lead to a serious acci-
dent with subsequent serious injury or
death.
Check the wheel centering.
Have the tightening torques, centering
and balancing of the wheel checked by
your Local
APRILIA
Dealer. These are
critical safety operations, and failure to
observe this warning could lead to an
upset with subsequent serious injury or
death.