APRILIA Caponord 1200 2016 Скачать руководство пользователя

Страница: 203 / 573

•

If the circuit is open: check the connector on the component and the Marelli control unit

connector: if not OK, restore. If OK, check cable continuity between the ENGINE PIN 53 and

component PIN 2 and restore the cable harness.

Internal rear cylinder injector P0206

•

short circuit to positive/ short circuit to negative / open circuit

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 67. If shorted to negative:

no voltage has been detected. If the circuit is open: an interruption has been detected.

Troubleshooting

•

If shorted to positive: disconnect the injector connector, set key to ON, activate the compo-

nent with the diagnosis instrument and check the voltage on the white/black cable on the

injector connector. If following the activation the voltage does not drop, restore the cabling,

otherwise replace the injector.

•

If shorted to negative: disconnect the injector connector, set the key to ON and check if there

is a ground connection on the White/Black cable: if there is connection, restore the cable

harness. If there is no connection, replace the injector.

•

If the circuit is open: check the connector on the component and the Marelli control unit

connector: if not OK, restore. If OK, check cable continuity between the ENGINE PIN 67 and

component PIN 2 and restore the cable harness.

Fuel pump

Function

Fuel pump: keeps pressure of the injectors supply

duct.

Low fuel: tells to the instrument panel about low

fuel

Operation / Operating principle

Low fuel: it is a resistance that if correctly supplied

varies its electrical resistance if it is damped or not

by petrol.

Level in electrical circuit diagram:

Injection load relay

Location:

•

on the vehicle: on the tank.

•

connector: near the fuel pump (4 ways,

black).

Caponord 1200 - Caponord 1200 Rally

Electrical system

ELE SYS - 203

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды

APRILIA Caponord 1200 2016, Руководство пользователя

Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды