Applied Precision RS 1130 Скачать руководство пользователя страница 4

Страница: 4 / 59

Reference Standard RS 2x30, RS 1x30

User’s Guide

RS-UG91-EN

www.appliedp.com

1. Safety Considerations and Instructions

This unit has been designed and tested according to EN 61010 standard and has left the

manufacturer’s premises in a state fully complying the safety standards.
In order to maintain the unit in a safe state and to ensure safe operation, the following instructions must
be reviewed and fully understood before operation:

▪

When the unit is to be permanently cabled, first connect an uninterruptible protective earth

ground conductor before making any other connection.

▪

If the unit is to be connected to other equipment or accessories, prior to energizing any unit

verify that common ground exists between them.

▪

Verify that the available mains voltage corresponds to specification of the unit.

▪

The Safety Class I unit provided with disconnectible AC supply cable and plug may only be

operated from a power socket with protective earth ground connection.

▪

Any interruption or loosening of the protective earth ground conductor either inside or outside

the unit or in an extension cable will cause a potential shock hazard that could result in personal
injury.

▪

The protective earth ground conductor shall not be interrupted intentionally.

▪

To avoid electrical shock do not remove protection or covers of the unit; refer to qualified AP

Service Center for maintenance of the unit.

▪

For continued protection against hazard, replace the line fuse(s) only with the same type and

current rating.

▪

Observe safety regulations and rules and also additional safety instructions whether specified

in manual for prevention of accidents.

Содержание RS 1130




























































Результаты поиска

Содержание RS 1130

Отзывы:

Похожие инструкции для RS 1130

Бренды по названию

Популярные бренды

Applied Precision RS 1130, Руководство пользователя

Результаты поиска

Содержание RS 1130

Отзывы:

Похожие инструкции для RS 1130

Бренды по названию

Популярные бренды