manualshive.com logo in svg

Applied Biosystems ViiA 7 Real, Краткое руководство пользователя

Поделиться
Скачать
Applied Biosystems ViiA 7 Real Скачать руководство пользователя страница 17

 

17

Maintain the ViiA

™

7 System

Applied Biosystems ViiA

™

7 Real-Time PCR System Quick Reference Guide

Clean the sample block

WARNING!

PHYSICAL INJURY HAZARD

. During instrument operation, the sample block and heated cover can be heated to 

100 °C. Before removing the sample block, be sure to wait until it reaches room temperature. 

IMPORTANT!

Wear powder-free gloves when you perform this procedure.

1

Remove the sample 
block

a.

Power off, then unplug the instrument and allow it to cool for 
15 minutes.

b.

Open the access door. 

c.

Firmly grasp the handle of the sample block, press the handle down, 
pull the sample block from the instrument, then place it on a clean, 
dry surface.

2

Clean the contaminated 
wells

a.

Pipette a small volume of deionized water into each contaminated well.

b.

Pipette the water up and down several times to rinse the well, then pipette the water to a waste 
beaker.

c.

Using a cotton swab, scrub inside of each contaminated well.

d.

Using a lint-free cloth, absorb the excess deionized water.

3

Install the sample block

a.

Load the sample block into the ViiA

™

7 System.

IMPORTANT!

After installing the sample block, confirm that the white 

indicator on the left side of the sample block is positioned behind the red line 
on the instrument rail. If the indicator is on the red line, push the sample 
block into the ViiA

™

7 System until it is seated correctly.

b.

Close the access door.

IMPORTANT!

Confirm that the instrument door is completely closed. The ViiA

™

7 Software 

displays an error message if the access door is not completely closed and latched, or if the 
sample block and heated cover are not seated correctly.

c.

Plug in, then power on the ViiA

™

7 System.

Содержание ViiA 7 Real























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды