Applied Biosystems 7300 Скачать руководство пользователя страница 58

Страница: 58 / 174

Chapter 3

Installing the Software and Powering On the Instrument

Troubleshooting

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Notes

Troubleshooting

This section contains:

•

Troubleshooting – Front Panel Indicators

page 32

•

Troubleshooting – Function Tests

page 33

Troubleshooting – Front Panel Indicators

Condition: The red

Error

indicator is lit.

1. Press on the instrument door to ensure that it is closed.

If the green Power On indicator lights up, the open instrument
door caused the error, and installation continues.

2. If the red Error indicator remains lit:

a. Open the instrument door.

b. Pull the heated cover door to verify that it is closed.

c. Close the instrument door.

If the green Power On indicator lights up, the open heated
cover door caused the error, and installation continues.

3. If the red Error indicator remains lit, verify that the Windows

desktop is displayed on the computer. If the Windows desktop
is not displayed:

a. Power off the 7300/7500/7500 Fast instrument.

b. Restart the computer.

c. Wait until the Windows desktop appears.

d. Power on the 7300/7500/7500 Fast instrument.

If the green Power On indicator lights up, installation
continues.

Instrument door

Heated cover door

Windows desktop

Содержание 7300















































































































































































Результаты поиска

Содержание 7300

Отзывы:

Похожие инструкции для 7300

Бренды по названию

Популярные бренды

Applied Biosystems 7300, Руководство по установке и обслуживанию

Результаты поиска

Содержание 7300

Отзывы:

Похожие инструкции для 7300

Бренды по названию

Популярные бренды