Applied Biosystems 2720 Скачать руководство пользователя страница 115

Страница: 115 / 151

107

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 9

Calibration verification test

Calibration verification test

Use this test to verify the temperature calibration of your GeneAmp

9600. The

calibration verification test consists of the following procedures, which you must
perform in sequence:

Setting up the 0.2-mL probe assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

107

Running the test

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

108

Calculating test results

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

109

Ending the test

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

110

PHYSICAL INJURY HAZARD.

Hot Surface. Use care when

working around the heated cover and sample block to avoid being burned by hot
components.

Required

equipment

This test requires the 0.2-mL Temperature Verification Kit

(PN 4317939), which

includes:

• Cotton swabs

• Light mineral oil

• 9600 temperature verification frame

• 0.2-mL probe assembly

• Model 4500 digital thermometer with a 9V battery installed

Setting up the

0.2-mL probe

assembly

1. If the heated cover is in the forward position, turn the knob counterclockwise

completely, then slide the heated cover back.

2. Place the 9600 temperature verification frame on the sample block.

3. Using a cotton swab, coat well E1 with mineral oil.

4. Place the 0.2-mL probe assembly into well E1.

5. Thread the probe wire through the channel in the 9600 temperature verification

frame to prevent damage to the probe and lead wires (see

Figure 18 on

page 106

6. Make sure the probe is connected to the digital thermometer.

7. Slide the heated cover forward, then turn the cover knob clockwise until the

white mark on the knob is aligned with the white mark on the cover.

IMPORTANT!

Seat the probe properly and the close the heated cover carefully.

If the probe wire is crushed when you close the cover, the probe can be
damaged.

8. Power on the digital thermometer.

Refer to the instructions in your Temperature Verification Kit for details on
operating the digital thermometer, Model 4500.

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды