Applied Biosystems 2720 Скачать руководство пользователя страница 117

Страница: 117 / 151

109

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 9

Calibration verification test

6. Press

ENTER

The temperature of the sample block and heated cover go to 95 °C, and the
following display opens:

This display shows the current temperature of the block cover (Cvr = xxC) and
sample block (Blk = xx.xC).

When the temperature of the block cover is within

10 °C of the sample block

temperature, the following display opens:

This display shows the current sample block temperature (“Blk=95.0C”) and a
clock that counts up from 0 in minutes and seconds (“Time=MM:SS”).

When the clock reaches 3 minutes, the following display opens:

7. Measure the temperature of well E1 using the digital thermometer. Record this

temperature as T(95).

IMPORTANT!

To end the test at any time, press the

STOP

key. This returns you

to the “Review History File” display. Press

, then press

ENTER

to return to the

Verify Calibration Diagnostic test.

The figure below shows temperatures during the calibration verification test.

Calculating test

results

Use the following information to calculate the results of the test. Refer to the
calibration label in your user manual for the High and Low Offset values.

Note:

If there is more than one GeneAmp

9600 in your laboratory, verify that the

serial number on the calibration label matches the serial number on the instrument
that you are testing.

Going to 95°C...

Cvr = xxC Blk = xx.xC

Wait 3 Minutes

Time=MM:SS Blk=95.0C

Record Temperature

Time=MM:SS Blk=95.0C

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды