Applent Instruments AT824 Скачать руководство пользователя страница 39

Страница: 39 / 52

Remote Control

Table 8-2 Notation Conventions and Definitions

Name of a parameter

[ ]

The content is optional

Select from several options

8.3.3

Parameter types

Parameters may be of four types as follows.

Table 8-3 Available data type

Format

Samples

<NR1> Integer

100,+100,-100

<NR2> Rational

1.23,+1.23,-1.23

<NR3> Floating-point 1.23E4, +1.23E4,-1.23E4,-1.23e-4

<NR4>

Floating-point

with

magnification

1.23K,1.23N,1.23U (magnification in following

Table)

Table 8-4 Magnification

Definition

Suffix

1E18 (EXA)

1E15 (PETA)

1E12 (TERA)

1E9 (GIGA)

1E6 (MEGA)

1E3 (KILO)

1E-3 (MILLI)

1E-6 (MICRO)

1E-9 (NANO)

1E-12 (PICO)

1E-15 (PEMTO)

1E-18 (ATTO)

8.4

Command Reference

All commands in this reference are fully explained and listed in the

following functional command order.



DISP Display subsystems



FUNC Function subsystem



FREQ Frequency subsystem



APER Speed subsystem



FETC? Result check subsystem

Содержание AT824





















































Результаты поиска

Содержание AT824

Отзывы:

Applent Instruments AT824, Руководство пользователя, Страница: 39 / 52

Результаты поиска

Содержание AT824

Отзывы: