Applent Instruments AT824 Скачать руководство пользователя страница 3

Страница: 3 / 52

Unpacking and Preparation

CERTIFICATION, LIMITED WARRANTY, &

LIMITATION OF LIABILITY

Applent Instruments, Inc.

(shortened form

Applent

) certifies that this product met its published

specifications at the time of shipment from the factory. Applent further certifies that its calibration

measurements are traceable to the People’s Republic of China National Institute of Standards and

Technology, to the extent allowed by the Institution’s calibration facility or by the calibration

facilities of other International Standards Organization members.

This Applent instrument product is warranted against defects in material and workmanship for a

period corresponding to the individual warranty periods of its component products.

The warranty

period is 1 year and begins on the date of shipment.

During the warranty period, Applent will, at

its option, either repair or replace products that prove to be defective. This warranty extends only to

the original buyer or end-user customer of a Applent authorized reseller, and does not apply to fuses,

disposable batteries or to any product which, in Applent’s opinion, has been misused, altered,

neglected or damaged by accident or abnormal conditions of operation or handling.

For warranty service or repair, this product must be returned to a service facility designated by

Applent. The buyer shall prepay shipping charges to Applent and Applent shall pay shipping charges

to return the product to the Buyer. However, the Buyer shall pay all shipping charges, duties, and

taxes for products returned to Applent from another country.

Applent warrants that its software and firmware designated by Applent for use with an instrument

will execute its programming instruction when properly installed on that instrument. Applent does

not warrant that the operation of the instrument, or software, or firmware, will be uninterrupted or

error free.

The foregoing warranty shall not apply to defects resulting from improper or inadequate

maintenance by the Buyer, Buyer-supplied software or interfacing, unauthorized modification or

misuse, operation outside the environmental specifications for the product, or improper site

preparation or maintenance.

THIS WARRANTY IS BUYER’S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. APPLENT SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA,

WHETHER ARISING FROM BREACH OF WARRANTY OR BASED ON CONTRACT, TORT,

RELIANCE OR ANY OTHER THEORY.

Applent Instruments, Inc.

Changzhou,

Jiangsu,

China,

Oct 2009 Rev.A3

Содержание AT824





















































Результаты поиска

Содержание AT824

Отзывы:

Applent Instruments AT824, Руководство пользователя, Страница: 3 / 52

Результаты поиска

Содержание AT824

Отзывы: