background image

24

Figure 4 – CONTROLS OF LIFT

LIFTING BUTTON (1)

0

When pressed, the power unit is running and the lift can be raised to a desired height until the
button is released. 

SAFETY RELEASE HANDLE (2)



When pressed, the mechanical safeties will be released so that the lift can be lowered.

LOWERING LEVER(3)

When   the   safety   release  handle  is   pressed   (the   mechanical   safeties   are   released),   press   the
lowering lever in the meantime to lower the lift to the desired height under its weight and the load
lifted until the lever is released. 

Please follow the instruction below if the control panel is equipped 

Figure 17 – CONTROLS OF LIFT

POWER SWITCH (1)

The power switch can be set in two positions:

0

0 position: 

the electric circuit is not 

powered; the switch can be padlocked to
 prevent the useof the lift. 

0

1 position: 

the electric circuit is 

powered.

PLIOT LAMP (2)



It shows that the electric circuit is 

Powered.

LIFTING BUTTON (3)

0

When pressed, the power unit is

 running and the lift can be raised to 
a desired height until the button is 

Fig.17

released. 

Lift operation can be summarized into three steps:

8.1.1  LIFTING

Pay attention to overhead clearance and The lift must be fully lowered and no one in the 
service area while the vehicle is driven onto the lift. 

If the jacking beam is equipped with the lift, it must be loweredfully. 
Position the wheels in center of each runway. 

Stop the vehicle when it contacts the front stops or at the desired position. 

Set the parking brake or place the wheel chops on each side of the rear wheels.
Make sure the all personnel must be exit before the lift is raised. 

Raise the lift by pushing the lifting button until reaching the desire height. 

8.1.2  STANDING

Press the lowering handle to engage the nearest mechanical safety.

Содержание HW-12S































Отзывы: