APlusLift HW-10KOH Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 19

background image

Step 5 (Installing Power Unit and Routing Hydraulic Hoses)



Mount the power unit onto the main side column with four hex bolts.



Connect two 4 1/4" fittings to both cylinders. Connect T-fitting to the power unit.



Connect short hydraulic hose to the power unit and the cylinder in power unit post.



Connect long hydraulic hose to the power unit and the cylinder in the opposite post.
Run the long hose over the overhead beam.



See figures below for hose layout and routing to the power unit. Do not over tighten the
fittings.

9

«
...
7
8
9
10
11
...
»

Содержание HW-10KOH




















Отзывы:

Нет отзывов

Похожие инструкции для HW-10KOH

Бренд: BUCKINGHAM MFG Страницы: 7

Бренд: TBM Страницы: 23

Бренд: Ravaglioli Страницы: 104

Over-Center 7k51

Бренд: Basta Boatlifts Страницы: 16

Бренд: MAHLE Страницы: 20

Бренд: Aqua Creek Products Страницы: 8

Бренд: morse Страницы: 6

Бренд: Peak Страницы: 41

Бренд: ALFRA Страницы: 29

Бренд: Halfen Страницы: 32

Бренд: VMI Страницы: 17

Бренд: VMB Страницы: 49

Бренд: Sav Страницы: 56

Бренд: Sav Страницы: 112

Бренд: Yale Страницы: 199

Бренд: MSW Motor Technics Страницы: 7

HYDRAFORCE LS-100

Бренд: Kasco Страницы: 19

Бренд: Ranger Products Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды