Aplex APC-3228 Скачать руководство пользователя страница 41

Страница: 41 / 106

APC-3228 User Manual

2E8/IRQ11 Set this value to allow the serial port to use 2E8 as its I/O port address and

IRQ11 for the interrupt address. This is the default setting. If the system will not
use a serial device, it is best to set this port to Disabled.



Serial Port5 Address

This option specifies the base I/O port address of serial port 5. The Optimal setting is

2E0



Serial Port5 IRQ

This option specifies the Interrupt Request address of serial port 5. The Optimal setting is

Option Description

Disabled Set this value to prevent the serial port from accessing any system resources.

When this option is set to

Disabled

, the serial port physically becomes

unavailable.

2E0/IRQ5 Set this value to allow the serial port to use 2E0 as its I/O port address and

IRQ5 for the interrupt address. This is the default setting. If the system will not
use a serial device, it is best to set this port to Disabled.

Содержание APC-3228











































































































Результаты поиска

Содержание APC-3228

Отзывы:

Похожие инструкции для APC-3228

Бренды по названию

Популярные бренды

Aplex APC-3228, Руководство пользователя

Результаты поиска

Содержание APC-3228

Отзывы:

Похожие инструкции для APC-3228

Бренды по названию

Популярные бренды