manualshive.com logo in svg

Aplex APC-3228, Руководство пользователя

Поделиться
Скачать
Aplex APC-3228 Скачать руководство пользователя страница 24

APC-3228 User Manual   

24

 

System Panel Connector (FPIO1) 

This connector supports several chassis-mounted functions. 

 

 

 

System Power LED (2-pin PWRLED) 

This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this 
connector. The system power LED lights up when you turn on the system power, and blinks when 
the system is in sleep mode. 

 

ATX Power Button/Soft-off Button (2-pin PWRSW) 

This connector is for the system power button. Pressing the power button turns the system on or 
puts the system in sleep or soft-off mode depending on the BIOS settings. Pressing the power 
switch for more than four seconds while the system is ON turns the system OFF. 

 

Hard Disk Drive Activity LED (2-pin HDLED) 

This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this 
connector. The IDE LED lights up or flashes when data is read from or written to the HDD. 

 

Reset Button (2-pin RESET) 

This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off 
the system power. 

Содержание APC-3228











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды