manualshive.com logo in svg

API A790, Руководство по эксплуатации

Поделиться
Скачать
API A790 Скачать руководство пользователя страница 46

 

Operating Your Computer 

2-23 

Using the Wireless LAN (Optional) 

Depending on your model, an internal Mini PCI wireless LAN (WLAN) 
card may have been pre-installed by your computer manufacturer at the 
factory. This card allows you to access corporate networks or the Internet 
in a wireless environment. 

The WLAN features include: 

z

 

Peer-to-Peer (Ad-Hoc) and Access Point (Infrastructure) modes 
support 

z

 

WEP (Wired Equivalent Privacy) 64/128-bit data encryption 

z

 

IEEE 802.11a/b/g standard compliance 

Technology 

802.11a 

802.11b 

802.11g 

Stated Maximum 
Throughput (Mbps) 

54 11 

54 

Data Rates (Mbps) 

54, 48, 36, 24, 18, 
12, 9, 6 

11, 5.5, 2, 1 

54, 36, 18, 9 

Band (GHz) 

5.15 ~ 5.35 

2.412 ~ 2.462 

2.4 

Modulation 
Technology 

OFDM (Orthogonal 
Frequency Division 
Multiplexing) 

DSSS (Direct 
Sequence Spread 
Spectrum) 

OFDM (Orthogonal 
Frequency Division 
Multiplexing) 

 

NOTE:

 802.11g mode is backward compatible with 802.11b mode. 

 

To take advantage of the WLAN feature, make sure that the PROSet 
driver is installed correctly (see chapter 6 for details). If your WLAN card 
was provided by your dealer instead of the computer manufacturer, 
contact your dealer for the correct driver to use. 

Configuring the WLAN 

After driver installation, you can use the WLAN utility to configure and 
monitor your WLAN connection. If you are using Windows XP, you can 
also use its built-in WLAN utility. Follow this procedure to launch the 
WLAN utility in Windows XP: 

1.

 

Select 

Control Panel

 

from the 

Start

 menu. 

Содержание A790











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды