background image

 

X-TELSTAR
Appearance after completing installation.

1

1. Motherboard installation:

1.1 Remove thumb screws from the 
      rear of the X-Telstar.

1.2 

Push handle forward to release 

      latch, then open and remove the 
      left side panel.

NOTE: Processor, memory, and expansion card installation 
is not covered in this manual. Please refer to each 
components’ documentation for instructions.

3

4

5

2.1 To install a floppy drive, remove the 
      3 1/2" drive housing by placing an 
      index finger into each inlet. Push side 
      rails toward one another, then gently 
      lift and slide outward. 

2.9 Align drive rails with inlets and slide 
      drive into place.

2.8 Locate 5 1/4" drive rails (inside 
      drive bay covers) and mount a 
      rail onto each side of the drive.

2.7 Remove 5 1/4" drive bay covers 
      by placing a finger into either
      inlet, firmly pressing inward,
      and opening.

2.6 

Return cage to drive bay.

2.5  Align screw holes on the underside of the drive 
       cage with those on the hard drive, and fasten.

2.4 Slide hard drive into cage.

2.2 Remove (unscrew) slot cover from 
      the slot to be used. Replace with 
      floppy drive, secure screws on both 
      sides, and return to drive bay.

2.3 For hard drive installation, locate and 
      remove one of the drive cages from 
      the bay. Secure clasps between index 
      fingers and thumbs. Squeeze clasps 
      toward each other while pulling 
      outward to release.

3.1 Locate the fan flow connector coming 
      from the front panel(black/yellow).     
      Select fan(s) to be regulated. Connect 
      the 4-pin male fan connector to the fan 
      flow controller. Adjust knob on front 
      panel to control airflow. (Up to 5 fans
      can be controlled via daisy chain.) 

Note: You may also leave a sensor loose in the chassis in order to monitor 
the ambient system temperature. 

DO NOT

 place the sensor directly on the 

CPU as it may cause system damage.

2. Install 3½”  and 5¼” drives:  

3.2 Locate the two temperature probes 
      coming from the front panel. Determine 
      which wire is which is by holding one of 
      the sensors between index finger and 
      thumb for a few seconds. Look to the 
      front display and note whether the 
      TMPE1 or TMPE2 indicator is increasing. 
      Mark the wire for easy identification. 

3.3 Place the TMPE1 probe on your CPUs heatsink. 
      Apply a small amount of tape to hold in place. 
      Use thermal tape for best results.

    

3. Connect fan flow controller and temperature probes:

4. LED display features:

4.1 The case fan monitor displays the current  
      fan use percentage.

(All screws and case keys are provided inside of the chassis.)

2

6

7

 

8

1.3 Remove the 2 thumb screws from the 
      motherboard tray area. 

Release the 

      motherboard tray by sliding it in the 
      direction shown. Remove tray from 
      the chassis.

1.5 

If your motherboard included an 

      IO shield, you must remove the 
      X-Telstar's IO shield. Use thumbs 
      or other object to push shield in-
      ward (cover area with a cloth to 
      avoid injury from metal edges). 

1.6 

Remove a slot cover for each slot 

      that corresponds with your expansion 
      card setup. Return motherboard tray 
      to the chassis. 

6. Identify power supply connectors (680W version):

9

CONTENTS

1.

 Motherboard installation..................................1

2. 

Install 3½” and 5¼” drives

..............................3

3. 

Connect fan flow controller and temperature probes....5

5. 

Connect front panel leads to motherboard.....................7

6.

.....................8

 

Identify power supply connectors

1.4 

Place motherboard on the tray. Make sure

      there is a standoff screw in place for each
      screw hole to be used on motherboard. 
      Align the motherboard with the standoff 
      screws and screw into place.
                                       

3.3 Place the TMPE2 probe on your hard disk drive.
      Apply a small amount of tape to hold in place. 
      Use thermal tape for best results.

    

5. Connect front panel leads to motherboard:

3.1 Locate the USB/Audio/1394(Firewire)
      front panel leads. Refer to your mother-
      boards’ documentation for pin placement
      instructions. Usually there is a triangular
      marking      on the lead to indicate the 
      positive wire. 

6.1 Once all components have been installed properly, gently return 
      the side panels to their initial positions and replace the screws. 
      Congratulations! You have completed assembly of your X-Telstar.

5.2 ATX 12V 4/8 Pin  connector X 1

7. 

Complete the Installation.....................................9

7. Complete the Installation:

3.2 

Locate the Power LED, HDD LED, Power 

      SW, Reset SW and Speaker front panel 
      leads. Again, refer to motherboard
      documentation for pin assignments. 

(Remove the right case panel to better access wiring.)
 

5.5 PCI-Express connector X 2

5.6 Floppy drive connector X 2

5.4 SATA drive connector X 4

5.3 PCI peripheral connector X 8

5.1 ATX 20/24 Pin connector X 1

8. USB/1394/Audio cable pin assignments:

8. 

USB/1394/Audio cable pin assignments.................9

4.3 TMPE1 and TMPE2 display the current
      temperatures of components that have 
      temp. sensors attached. The H.D.D 
      indicator displays hard drive activity.

4.4 The “Voice Unit” display allows you to 
      monitor your PCs dynamic audio 
      levels. 

4.2 The 5V/12V monitor displays the current voltage 
      values of the 5 and 12 volt rails respectively.
      Red areas indicate very low/high voltages.

4. 

LED display features..................................................6

500W version connectors: 1 x (20 + 4 pin)   1 x 12V (P4)
                                            2 x SATA   8 x PCI   2 x Floppy

Содержание X-Telstar














Отзывы: