background image

8

CARE AND MAINTENANCE

ARGHD60SS

WARNING

Always switch off the electricity supply before 

performing maintenance work. In the event of a 

fault, contact customer services.

CAUTION

Use soapy water and a cloth for cleaning. Never use 

abrasive powders.
Avoid banging pots and pans down on the hob.
Do not leave any empty pan on the heating zone

HOW TO KEEP YOUR HOB IN GOOD 

CONDITION 

Before cleaning your oven, or performing maintenance, 

disconnect it from the power supply.
The appliance should be cleaned after use.
Wipe the inner and outer surface of the appliance and its 

accessories with wet cloth.

removed with a cloth.

The surface of the hob may be easily cleaned as follows:
Cleaning of enamel parts:
To maintain the features of the enamel parts, wash 

frequently with soapy water.
Never use abrasive powders. Avoid leaving acid or alkaline 

substances on the enamel parts (vinegar, lemon juice, salt, 

tomato juice, etc.) and washing the enamel parts while 

they are still warm.
Cleaning of stainless steel parts:
Wash these parts with soapy water and then dry them 

with a soft cloth.
The shine is maintained by regularly cleaning them with 

special products normally commercially available. Never 

use abrasive powders.

cleaned by simply removing them and washing them with 

soapy water. After drying them well and checking that the 

holes are not blocked, put them back into their correct 

position.

FUSE

USE  A 30 AMP FUSE

DOUBLE POLE SWITCHED

FUSED SPUR OUTLET

ON

GAS CONNECTION

CHANGING THE NOZZLES

Lift up the burners and unscrew the nozzle using an 

dedicated tool and replace the nozzles with those designed 

for LPG gas supply

CAUTION

The hob installation and burner changes must be carried 

out by a competent person, e.g. a gas safe registered 

NOTE

The LPG nozzles are provided in a separate bag marked 

“LPG” and if they are changed and the natural gas jets 

retained then the label should be changed to “NATURAL”.

REGULATION OF BURNERS

Regulation of the “MINIMUM” position on the burners.
To regulate the minimum position on the burners, follow 

the procedure below:

Turn on the burner and turn the knob to its MINIMUM 

Remove the knob from the tap set for standard pressure. 

The knob is found on the bar of the tap itself.
Place the tap bar on the work top, use a small screwdriver 

the burner is regulated in the most 

suitable manner to MINIMUM.

go out when changing the position 

quickly from MAXIMUM to MINIMUM 

position.

[conversion

nozzles] x 4

x1

[conversion

nozzles]

[conversion

nozzles] x 4

x1

[conversion

nozzles]

Содержание ARGHD60SS

















Отзывы: